The pin is released which allows the piston to move

Assignment Help Mechanical Engineering
Reference no: EM13608201

A piston held by a pin in an insulated cylinder, shown in Figure above (right), contains 2 kg water at 100C, quality 98%. The piston has a mass of 102 kg, with cross-sectional area of 0.1 m2, and the ambient pressure is 100 kPa. The pin is released, which allows the piston to move. Determine the final state of the water, assuming the process to be adiabatic.

Reference no: EM13608201

Questions Cloud

A bank estimated the average amount of money withdrawn from : a bank estimated the average amount of money withdrawn from its atm machines over weekends exceeds 150 per customer
Determine the forces exerted by the vane on the water if v1 : a jet of water with a velocity v1 striking a vane45 degrees that is moving with a velocity vo. determine the forces
Three grams of musk oil are required for each bottle of : three grams of musk oil are required for each bottle of mink caress a very popular perfume made by a small company in
The following experimental data relates the observed : experiments have shown that when a clean tungsten surface is heated by laser irradiation using a focused ruby laser the
The pin is released which allows the piston to move : a piston held by a pin in an insulated cylinder shown in figure above right contains 2 kg water at 100c quality 98. the
Replenished the petty cash fund based on the following : replenished the petty cash fund based on the following summary of petty cash receipts office supplies 189
The tyus company has provided the following data for the : the tyus company has provided the following data for the month of july raw materials july 1 15000 july 31 ? work in
Assuming normality test the hypothesis that the true : specimens of blood from 10 different animals were analyzed for blood count say y in units of 100 and packed cell volume
Company xx has multiple divisions for production of windows : company xx has multiple divisions for production of windows. the frames are produced in the frame division. when

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Te local acceleration of gravity is 981 ms2 determine the

a gas is contained in a vertical frictionless pixton-cylinder. the piston m 10 kg a- 7.5 x 10-3 m2 is attached to a

  Explain an ideal vapor-compression refrigeration cycle

An ideal vapor-compression refrigeration cycle uses R-134a as the working fluid in an air-conditioning system. The refrigerant enters the compressor as a saturated vapor at 40 °F

  A flywheel can be considered as being composed of a thin

a flywheel can be considered as being composed of a thin disc and a rim. the rim weighs 322 lb and has diameters of 24

  A 15-tooth pinion having a pressure angle of 25ordm and

a 15-tooth pinion having a pressure angle of 25ordm and module of 8mm is to drive an 18-tooth gear. determine for both

  Determine the minimum size of the snow shoes needed

Consider a 70-kg woman who has a total foot imprint area of 400 cm2. She wishes to walk on the snow, but the snow cannot withstand pressures greater than 0.5 kPa. Determine the minimum size of the snow shoes needed.

  Determine the total heat transfer and the total work

Determine the total heat transfer and the total work(kj). and show the T-V diagram.

  A component is fully constrained with 0 dof

An engineer insists that a component is fully constrained with 0 DOF because 2 plates are bolted together with 4 screws (assuming one of the 2 plates is considered "grounded"). Is he / she correct? Explain why or why not using concepts discuss..

  Determine the magnitude of the force p

two solid cylinders rods AB and BC are welded together at B and loaded. determine the magnitude of the force P for which the tensile stress in rod AB is twice the magnitude of the compressive stress in rod BC?

  What is the design objective

2. What is the design objective? -to minimize the required power input to the compressors 3. What parameters does the design engineer control?

  Calculate the flow energy per pound-mass enthalpy and

calculate the flow energy per pound-mass enthalpy and total enthalpy. two kilograms of ammonia at 200kpa .755 m3kg and

  If a sludge containing 70 water and 30 solids is passed

sludge is wet solids that result from the processing in municipal sewage systems. the sludge has to be dried before it

  A small 06-lb collar d can slide on portion ab of a rod

a small 0.6-lb collar d can slide on portion ab of a rod which is bent as shown. knowing that r 8 in and that the rod

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd