The performance of an ammonia absorption cycle refrigerator

Assignment Help Mechanical Engineering
Reference no: EM13632276

The performance of an ammonia absorption cycle refrigerator is to be compared with that of a similar vapor-compression system. Consider an absorption system having an evaporator temperature of ?10°C and a condenser temperature of 50°C. The generator temperature in this system is 150°C. In this cycle 0.42 kJ is transferred to the ammonia in the evaporator for each kilojoule transferred from the high-temperature source to the ammonia solution in the generator. To make the comparison, assume that a reservoir is available at 150°C, and that heat is transferred from this reservoir to a reversible engine that rejects heat to the surroundings at 25°C. This work is then used to drive an ideal vapor-compression system with ammonia as the refrigerant. Compare the amount of refrigeration that can be achieved per kilojoule from the high-temperature source with the 0.42 kJ that can be achieved in the absorption system.

Reference no: EM13632276

Questions Cloud

An electron is projected with an initial speed of 39 x105 : an electron is projected with an initial speed of 3.9 x105 ms directly toward a proton that is fixed in place. if the
The barometric pressure is reported to be 6055 torr and the : 1 the barometric pressure is reported to be 605.5 torr and the temperature of the water is 22.5 c what is the pressure
Consider a small ammonia absorption refrigeration cycle : consider a small ammonia absorption refrigeration cycle that is powered by solar energy and is to be used as an air
Which does not slip against the road surface since the : the wheel of a car has a radius of .350 m. the engine of the car applies applies a torque of 295 n m to this wheel
The performance of an ammonia absorption cycle refrigerator : the performance of an ammonia absorption cycle refrigerator is to be compared with that of a similar vapor-compression
Knowing that v -4 ms at t0 and v20 ms at t 4 determine : the acceleration of a particle is defined by a kt2. knowing that v -4 ms at t0 and v20 ms at t 4 determine the
A 100 kg glider attached to a spring with a force constant : a 1.00 kg glider attached to a spring with a force constant 49.0 nm oscillates on a horizontal frictionless air track.
Calculate the percentage volume change for a material being : a calculate the percentage volume change for a material being transformed from fcc to bcc. remember to assume the
A sail plane with a lift-to-drag ratio of 25 flies with a : a sail plane with a lift-to-drag ratio of 25 flies with a speed of 50 mph. it maintains or increases its altitude by

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the compression ratio of the cycle

an air-standard otto cycle uses 0.1 kg of air and has a clearance of 17%. THe intake conditions are 98 kPa and 37 C and the energy released during combustion is 1600 KJ/kg. What is the compression ratio of the cycle?

  Steam enters an adiabatic turbine at 10 mpa and 500 degc

steam enters an adiabatic turbine at 10 mpa and 500 degc and leaves at 10 kpa with a quality of 90. neglecting

  Describe some of the important steps in the preparation of

1- describe some of the important steps in the preparation of a written document. what role do written documents play

  The top of the tube represents 0 lbfin2 absolute then at an

a water barometer was observed at a school on a recent trip. it was basically a tube filled with water in a container.

  Find1 the work performed by the gas b the increase in the

an isobaric heating process raises the temparature of one of one mole of an ideal gas by delta t 100 k. the heat

  A vibrating system has a mass m 10kg suspended from a

a vibrating system has a mass m 10kg suspended from a spring of modulus k 2500nm nd damping amunts to c 45 nsm.

  Calculate the head provided by the pump

Calculate the head provided by the pump and Calculate the brake power required if the pump efficiency is 75% (kW).

  If upon initial null balance r3 is 1275 ohms and if when r2

a simple wheatstone bridge as shown in fig. 7.10 is used to determine accurately the value of an unknown resistance r1

  Determine the volume of chamber

the entire assembly is placed in an environment whose temperature is 200c. determine the volume of chamber 1 when thermodynamic equillibrium has been estabilished.

  Meet the goal as well as the positive and negative aspects

Discussion of various cycles attempted to meet the goal as well as the positive and negative aspects of your design.

  Determine the max height

The tank cover is airtight, and the pressure above the water surface is 2 atm gage. The system is at sea level. Determine the max height to which the water stream could rise.

  Show step by step how you will conduct data acquisition and

a steel mill has a production set up where metal sheets are rolled for desired thickness as they emerge from the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd