The motor will operate in a continuous mode in an ambient

Assignment Help Electrical Engineering
Reference no: EM13477779

1.   Describe the key features of dc and ac motors:-

2.   Describe the main methods of starting A.C motors

3.   Describe the advantages and disadvantages of star delta starting

4.   How can the speed and direction of a three phase synchronous motor be controlled

5.   Describe the main factors affecting the selection of an electric motor

6.   Give an example and explanation of the information on a typical motor nameplate.

7.   You have been asked to source a motor ( and starter) capable of powering an escalator; The following information is to be used:-

a)   Angle of escalator = 30deg

b)   Rise = 8m

c)   Each tread = 0.4m

d)   Each tread could have 1 person ( assume 75kg per person)

e)   The escalator rises from bottom to top in 20 seconds

f)    Assume 2kW of load due to friction

g)   The motor will operate in a continuous mode in an ambient temperature between 10 and 30 deg C. The maximum temperature increase is 70 deg C

 

Reference no: EM13477779

Questions Cloud

Dscribe the impact and the vulnerability of the scada : scada wormprotecting the nations critical infrastructure is a major security challenge within the u.s. likewise the
Productivity can be boosted with more variety in work : hypothesis sthe hypothesis should provide a logical response to the research questions provided by the managers dilemma
Manufacturing companies have the common issue of high : manufacturing companies have the common issue of high turnover rate with their employees. pay is not always the reason
Research change management models and address the following : organizations like all cultures must continue to evolve or they stagnate and eventually become obsolete. using change
The motor will operate in a continuous mode in an ambient : 1.nbspnbsp describe the key features of dc and ac motors-2.nbspnbsp describe the main methods of starting a.c
Write-word paper describing a single informal learning : write-word paper describing a single informal learning experience that someone could have.you may describe for example
Compute the value of a common stock if the firms earnings : 1. what is the value of a common stock if the firms earnings and dividends are growing annually at 10 the current
The paper is to be your original work and written solely : ethics and morals in business managementyou will write a research paper of 8 full -9 full pages on a management topic.
Describe what the ring of fire is and how it is associated : explain what the ring of fire is and how it is related to plate tectonics. focus your attention on the ones that have

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the magnitude of the impedance in ohms

1. Determine the magnitude of the impedance inohms for a 65 mH inductor with excitation at 750 rad/s. 2. Determine the magnitude of the impedance inohms for a 80 mH inductor in series with a 80 ohm resistor.

  What is the peak frequency deviation and modulation index

A sinusoidal modulating waveform of amplitude 4V and frequency 1 kHz is applied to an FM exciter that has a modulator gain of 50 Hz/V. What is the peak frequency deviation. What is the modulation index

  Youve just been hired as a process engineer at a major

youve just been hired as a process engineer at a major silicon chip manufacturer and your boss gives you a first

  Find quantized output for each of sample values of signals

Two Bit Analog to Digital Converter - MATLAB Let x (t) = 0.8 cos(2*pi*t) + 0.15, 0≤ t ≤ 1, and zero otherwise, be the input to a two bit ADC converter. a.) For a sampling period Ts = 0.025 sec; determine and plot using MATLAB the sampled signal: x (n..

  Design to test an op-amp based instrumentation amplifier

Design (simulaton, analysis), build and test an op-amp based instrumentation amplifier with the following specifications: (a) Have very high input resistance (minimum is 1 Mega Ohm). (b) Have very high voltage gain (minimum 1000V)

  Specify requirements on adc and appropriate analog signals

A calibrated RTD a = 0.0041/°C, R=306.5-ohm at 20°C, and PD= 30mW/ °C will be used to measure a critical reaction temperature. Temperature must be measured between 50 °C and 100 °C with a resolution of at least 0.1°C.

  How many additional circuit breakers must be purchased

An industrial plant is to be supplied by three identical transformers. A decision must be made whether to purchased afourth transformer to build a sparing transformer system oralternatively, to configure the source as a secondary selective system.

  Determine the change in output voltage for a temp change

At 0°C the circuit is balanced and at this temperature the RTD has a resistance of 200 W. Determine the change in output voltage for a 1°C change in temperature now assuming the meter has an internal impedance of 8,000 W.

  What sources to pick to get total absorbed power

what sources to pick to get total absorbed power and total delivered power, since a,e,f, and h absorb and b,c,d,and g supply and for total they suggest a+c+d+e+c=absorbed and b+g+f=delivered

  Sketch fourier transform for the singly-balanced mixer

Let the input to a singly-balanced mixer, f(t), be given by V0 Sin (2 pi fs t). The local oscillator input p(t) is a square wave, alternating between 0 and +1 volt. The freqency of the square wave is 10 MHz, while for the input, fs is 100 KHz.

  Find the expression for the voltage across inductor for t

The current in a 20 mH inductor is known to be i = 40 mA, t 0.

  Where can i find a copy of the answers to textbook review

where can i find a copy of the answers to textbook review questions in the industrial motor control 6 th edition by

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd