User Account

All Pages

The mechanical effficiency of the system is 80 what is the

Assignment Help Mechanical Engineering
Reference no: EM13614038

It takes 15 seconds to raise a 1200 kg car and the supporting 300 kg hydraulic lift platform to a height of 2.8 m. The mechanical effficiency of the system is 80%. What is the average power input in Watts necessary to accomplish this? Assume constant velocity.

Reference no: EM13614038

Questions Cloud

Bob can afford monthly car payments of 200 for four years : bob can afford monthly car payments of 200 for four years. what is the most expensive car bob can buy if the
After six months of operation brothers lawn service hadthe : after six months of operation brothers lawn service hadthe following revenue and expense account
Show the cycle on a t-s diagram with respect to the : consider a 210mw steam power plant that operates on a simple rankine cycle. steam enters the turbine at 10mpa and 500oc
Kleener co acquired a new delivery truck at the beginning : kleener co acquired a new delivery truck at the beginning ofits current fiscal year. the truck cost 26000 and has an
The mechanical effficiency of the system is 80 what is the : it takes 15 seconds to raise a 1200 kg car and the supporting 300 kg hydraulic lift platform to a height of 2.8 m. the
Johnny is running home from school to watch his favorite : a johnny is running home from school to watch his favorite soap opera as the stomach turns. he runs 6 blocks east to a
Basket purchase allocation crow co purchased some of : basket purchase allocation crow co. purchased some of themachinery of hare inc. a bankrupt competitor at a liquidation
What two accounts will be affected while recording entries : what two accounts will be affected while recording entries inthe general ledger when you bill a customer for services
A boat has a mass of 6020 kg its engines generate a drive : a boat has a mass of 6020 kg. its engines generate a drive force of 3350 n due west while the wind exerts a force of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A steel plate which is 15 m by 15 m and 30 mm thick is

a steel plate which is 1.5 m by 1.5 m and 30 mm thick is lifted by four cables attached to its corners that meet at a

  Determine the angle theta degrees

However, even when the cylinder is pressurized, the torque T is still sufficient to keep the seam closed so that no water leaks out. Determine the angle theta degrees that requires the minimum torque T to keep the seam closed. (Hint: use Mohr's ci..

  Calculate athe mass of the air that has entered the tank

a 1-m3 rigid tank initially contains air at 150 kpa 300 k. the tank is connected through a valve to a supply line at

  The rate of heat transfer to the air is 350 kjkg neglecting

air enters a device operating at steady state at 18 bar and 572 k and leaves at 1.5 bar and 520 k with a volumetric

  Calculate the number of vacancies at 546degc given that the

the number of vacancies present in some metal at 857degc is 1.7 x 1024 m-3. calculate the number of vacancies at

  Draw in third angle projection

Draw in Third Angle Projection. the following orthogonal views - a Sectional Side View from 8 on a vertical cutting plane through the centre line of the bearing journals

  Calculate the final pressure and volume of the system

The process and volume relation is given p=(8-4v)bar for a non flow process ,where V is in cubic meter.If 130kJ of work is supplied to the system,calculate the final pressure and volume of the system.Take the initial volume as 0.5 cubic meter.

  Which one has the bigger moment of inertia

two spinning discs have the same angular momentum, but disk 1 has more kinetic energy than disk 2. Which one has the bigger moment of inertia - explain your reasoning?

  Find max specific range and max range airspeed

Find Max Level Airspeed at 95% RPM and find Max Range Airspeed (VBR) and Max Endurance Airspeed (VBE) - find Max Specific Range and Max Range Airspeed

  A boat travels at a constant speed of 15 ms around the

a boat travels at a constant speed of 15 ms around the circumference of a half circle in a time span of 45 s. what is

  Just before it lifts off a 10500 kg airplane is traveling

just before it lifts off a 10500 kg airplane is traveling at 60 fts. the total horizontal force exerted by the planes

  Explain vector integral - stokes therom

Vector integral - stokes therom, Evaluate the line integral by stokes theorem (clock wise as seen by a person standing at the origin).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd