The loading produes a gross nominal tension stress of 45

Assignment Help Mechanical Engineering
Reference no: EM13613495

A very wide sheet of 7075-T651 aluminum plate, 8mm thick is found to have a single-edge through-the-thickness crack 25 mm long. The loading produes a gross nominal tension stress of 45 MPa perpendicular to the plane of the crack tip.

a. Calculate the stress intensity factor at the crack tip.

b. Determine the critical stress-intensity factor.

c. Estimate the factor of safety (n = K1c/k1)

Reference no: EM13613495

Questions Cloud

On june 30 20x5 maine lobster purchased a patent for a new : on june 30 20x5 maine lobster purchased a patent for a new freezing process at a cost of 33600. it estimated that the
If the ball is in contact with the wall for 315 ms what is : a 49.0-g super ball traveling at 30.0 ms bounces off a brick wall and rebounds at 15.0 ms. a high-speed camera records
Prepare a direct materials budget showing the quantity of : pearl products limited of shenzhen china manufactures and distributes toys throughout south east asia. five cubic
A particle moves according to the equation x 8t2 where x : a particle moves according to the equation x 8t2 where x is in meters and t is in seconds. a find the average velocity
The loading produes a gross nominal tension stress of 45 : a very wide sheet of 7075-t651 aluminum plate 8mm thick is found to have a single-edge through-the-thickness crack 25
Suppose a trucks mass is 2000 kg while the cars mass is : suppose a trucks mass is 2000 kg while the cars mass is 1000kg. and suppose the truck slows down by 5 ms during the
Gunner construction has consistantly used the : gunner construction has consistantly used the percentage-of-completion method of recognizing revenue. during 2014
The moisture x of the wet mix of a product is considered to : the moisture x of the wet mix of a product is considered to have an effect on the density y of the finished product.
The taxable income includes 5000 of gain from a capital : jane and blair are married filing jointly and have 2012 taxable income of 97000. the taxable income includes 5000 of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  After concentration the stream water becomes water

saturated steam with 120.8 kpa is used to concentrate 1000 kgh of juice from 12 to 20 solids at 95degc steam and juice

  Therefore is constrained to move in a circular arc of

the particle a is mounted on a light rod pivoted at o and therefore is constrained to move in a circular arc of radius

  Presuming that the bomb is perfectly insulated

Assuming that the bomb is perfectly insulated what is the temperature of the air in the bomb at the end of filling process? Assume air is an ideal gas with constant specific heats in a ratio Cp/Cv = γ = 1.4 and constant R= 287 J/kg K.

  Find the pitch diameter of the pinion

find: a) the pitch diameter of the pinion. b) the pitch diameter of the gear. c) the output torque of the gear. d) the minimum length of the key used to attach the gear?

  Determine the capacity of a cylindrical tank

Find the capacity of a cylindrical tank that is 250 feet in diameter and 30 feet high? In the above problem, what is the capacity if the tank is 75% full, and what is the capacity in gallons?

  Mainframe computing is way to manage enterprise data

Mainframe computing used to be the only way to manage enterprise data. Then personal computers changed the data management scene. How do these two computing styles differ, and how did shift to PC-based computing evolve.

  Calculate the actual a/f ratio and do a wet

Find the stoichiometric A/F ratio (by mass) for the combustion of benzene (C6H6). Compute the actual A/F ratio and do a wet and dry analysis of the products by volume at a mixture strength of 95%.

  Find the shaft id needed to obtain a maximum deflection

Find the shaft ID needed to obtain a maximum deflection at the center of 3 mm if the shaft OD is 22 cm. Assume the shaft to be the same length between supports as the length of the paper roll.

  Draw the front view - third angle projection

Partial Auxiliary View showing the details of the inclined face - supply dimensions for the inclined face only. Select a suitable scale to make the drawing fit on an A3 drawing sheet.

  Sketch three-dimensional views of the unit cell of a bcc

a sketch three-dimensional views of the unit cell of a b.c.c. crystal showing a 100 plane a 110 plane a 111 plane and a

  The isentropic efficiencies for the turbine and pump are 85

a cycle based on a rankine cycle with water as the work fluid must have its highest cycle pressure and temperature at

  Determine tc for 2024-t6 aluminum assume the

wetting of some metallic surfaces can be inhibited by means of ion implantation of the surface prior to its use thereby

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd