The limestone scrubber operates with an efficiency of 90

Assignment Help Mechanical Engineering
Reference no: EM13640949

A 1000 MW coal fired power plant operates with an annual plant capacity factor equal to 75%. The plant burns coal which has a heating value of 12,000 Btu/lbm. The average ash content is 8% by mass, and the average sulfur content of 2% by mass. The overall heat rate of the plant is 9000 Btu/kWh. The limestone scrubber operates with an efficiency of 90%, and the ESP operates with an efficiency of 95%. (a.) estimate the quantity of coal burned in one year, in short tons ( 1 ton = 2000 lbm). (b.) taking the answer from part (a.) as 2.0 x 106 ton, estimate the amount of dry waste product formed in the FGD system and in the ESP. Assume that the overall reaction is CaCO3 + SO2 + 2H2O => CaSO3 . 2H2O + CO2. and that the dry waste product from the scrubber is 70% CaSO3 . 2H2O and 30% CaCO3, by mass. (MCa = 40, Ms = 32). Assume that 10% of the ash falls to the bottom of the furnace, and the remainder is carried via the gas stream to the ESP.

Reference no: EM13640949

Questions Cloud

Fe2o3 2al - 2fe al2o3if you start with 500g of iron iii : fe2o3 2al - 2fe al2o3if you start with 50.0g of iron iii oxide and 25.0 g ofaluminum in the above problem what is the
Calculate the annual amount of limestone mls used if 35 : a midwestern power plant burns 2 x 106 tons of coal annually. the coal contains 2 sulfur by weight. a limestone
Te normal boiling point for a solutionof n-hexane c6h14 m : the normal boiling point for a solutionof n-hexane c6h14 m 86.18 gmol and n-octane c8h18 m 114.23 gmol is t 93.7
An aluminum rod is 37cm long at 351 degree celcius and has : an aluminum rod is 37cm long at 35.1 degree celcius and has a mass of 522g. if 20400 j of energy is added to the rod by
The limestone scrubber operates with an efficiency of 90 : a 1000 mw coal fired power plant operates with an annual plant capacity factor equal to 75. the plant burns coal which
What is the ratio of the conjugate base concentration to : phenolphthalein is a commonly used indicator that is colorless inthe acidic form ph lt 8.3 and pink in the basic form
The height of the cliff is 900 m and the speed with which : the height of the cliff is 9.00 m and the speed with which the stones are thrown is 14.00 ms. write an algebraic
Estimate the required filter length for a bed efficiency : a fibrous filter bed is to be designed with a solid fraction equal to 0.1 fiber diameter equal to 10m and filter
Many many snails have a one-mile race and the time it takes : many many snails have a one-mile race and the time it takes for them to finish is approximately normally distributed

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd