User Account

All Pages

The isentropic efficiency is known from manufacturers data

Assignment Help Mechanical Engineering
Reference no: EM13630242

An insulated turbine is operating on nitrogen. The gas enters at 3.8 atm, 170°C and expands to 1 atm. The isentropic efficiency is known from manufacturer's data to be 83.2% in this situation. Determine the temperature at the turbine's exit (°C). Assume constant specific heats.

Reference no: EM13630242

Questions Cloud

A 377-kg ball of clay is thrown downward from a height of : a 3.77-kg ball of clay is thrown downward from a height of 3.47 m with a speed of 4.81 ms onto a spring with k 1690
A 132 kg axial load is uniformly carried by an aluminum : a 13.2 kg axial load is uniformly carried by an aluminum pipe with an outside diameter of 10.0000 cm and an inside
A 255-kg model rocket is launched vertically upward with : a 2.55-kg model rocket is launched vertically upward with sufficient initial speed to reach a height of 2.83middot102 m
Helium has the lowest normal boiling point of any of the : helium has the lowest normal boiling point of any of the elements at 4.2 k. at this temperature the enthalpy of
The isentropic efficiency is known from manufacturers data : an insulated turbine is operating on nitrogen. the gas enters at 3.8 atm 170degc and expands to 1 atm. the isentropic
Both the plane and the horizontal surface have a : a spring with a spring constant of 549 nm is used to propel a 0.275-kg mass up an inclined plane. the spring is
Calculate a 99 two-sided confidence interval on the : an article in knee surgery sports traumatology arthroscopy 2005 vol. 13 pp. 273-279 arthroscopic meniscal repair with
Determine a the rate of heat loss from the compressor b the : consider an r-134a compressor on a refrigeration system. if the refrigerant enters as saturated vapor at 200 kpa 0.03
A city council consists of 7 males and 4 females two : a city council consists of 7 males and 4 females. two councilors are selected at random to represent the city. what is

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the number of miles the airplane traveled

An airplane was moving with a velocity equal to 300 mph when the velocity was increased with uniform acceleration to 600 mph in 5 min, calculate the number of miles the airplane traveled during that interval of time.

  Dtermine a the finite difference equations b the nodal

a plane wall with surface temperature 350c is attached with straight rectangular fins k 235 wm k. the fins are exposed

  Natural gas at 70 f and standard atmospheric pressure of

natural gas at 70 f and standard atmospheric pressure of 14.7 psi is compressed isentropically to a new absolute

  Knowing that es29x106 psi and ea101x106 psi determine a the

compressive centric forces of 30 kips are applied at both ends of the assembly shown by means of rigid end plates.

  All elbows are 90 degrees with k factor 075 pipe lengths

for the fluid power system shown in figure determine the external load f that the hydraulic cylinder can sustain while

  A 1-m3 rigid tank has propane at 100 kpa 300 k and

a 1-m3 rigid tank has propane at 100 kpa 300 k and connected by a valve to another tank of 0.5 m3 with propane at 250

  Enter the combustion chamber of the capstone

1. Natural gas and 100% excess air enter the combustion chamber of the Capstone micro-gas turbine at 400 kPa and 452 °C.

  A tennis racket hits a tennis ball with a force of fat-bt2

a tennis racket hits a tennis ball with a force of fat-bt2 where a1 1280 nms b1 460 nms2 and t is the time in

  Determine the largest mass m

the pin c will support a force of 24 knmagnitude.Based on this criterion, you are asked to determine the largest mass m that the frame can safely support.the diameter of pulley at d is given as 0.2 m.find maximum mass m that can be supported by fr..

  How larger surface edge crack can the advanced ceramics

conventional ceramics have a fracture toughness of about 5 while advanced ceramics may have 20. determine1 how larger

  A force is described as 150 lb acting through the origin

a force is described as 150 lb acting through the origin of a two dimensional coordinate system up at an angle 135ordm

  List the materials you find and state their significant

a company wishes to enhance its image by replacing oil-based plastics in its products by polymers that are based on

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd