The isentropic efficiencies of turbine and compressor are

Assignment Help Mechanical Engineering
Reference no: EM13620534

Question1

A piston cylinder device contains 25 g of saturated water vapor that is maintained at constant pressure of 300 kPa. A resistance heater within the cylinder is turned on and pass a current of 0.2 A for 5 minutes from a 120-V source. At same time, a heat loss of 3.7 kJ occurs. Determine the change of entropy of the steam.

1.6 kg of air is compressed according to the law pV1.3=C form a pressure of 1.2 bar and temperature of 20 oC to a pressure of 17.5 bar. Calculate the change in entropy.

Question 2

An engine works on ideal dual cycle draws air at 1 bar pressure and 30 oC. The compression ratio is 16 and the pressure ratio is 1.75. The total heat added is 2500 kJ/kg.

Sketch the cycle on a p-v diagram

Determine the following:

a. Pressures, temperatures and specific volumes at the salient points, heat added at constant pressure process and cut-off ratio.

b. Thermal efficiency of the cycle.

c. Mean effective pressure for the cycle.

Take Cp=1.005 kJ/kg K, Cv=0.718 kJ/kg K, g=1.4, R=287 J/kg K.

Question 3

A gas turbine unit has a pressure ratio of 9 and a maximum cycle temperature 900 K. the compression take place in two stages of equal pressure ratio with intercooling back to initial temperature of 15 oC. The isentropic efficiencies of turbine and compressor are 0.86 and 0.89 respectively . The unit is fitted with a heat exchanger of 70 % effectiveness.

1. Sketch the cycle on a T-s diagram

2. Determine the efficiency of the unit.

Reference no: EM13620534

Questions Cloud

An electron accelerated from rest through a voltage of : an electron accelerated from rest through a voltage of 490v enters a region of constant magnetic field. if the electron
Khc is considering an investment project that requires a : khc is considering an investment project that requires a new machine for producing special tools. this new machine
Write a matlab program that determines the probability of 4 : write a matlab program that determines the probability of 4 of a kind in a 5-poker draw. dont use formula. create a
Assume that none of the alpha particles bounced back from : a physicist has developed a device that generates a beam of alpha particles each of which is a helium nucleus
The isentropic efficiencies of turbine and compressor are : question1a piston cylinder device contains 25 g of saturated water vapor that is maintained at constant pressure of 300
Nanometrics inc has a beta of 367 if the market return is : nanometrics inc. has a beta of 3.67. if the market return is expected to be 13.00 percent and the risk-free rate is
What is the peak voltage across the capacitor the generator : an ac generator supplies an rms voltage of 110 v at 60.0 hz. it is connected in series with a 0.650 h inductor a 5.40
Last year joan purchased a 1000 face value corporate bond : last year joan purchased a 1000 face value corporate bond with an 7 annual coupon rate and a 25-year maturity. at the
If each pellet is in contact with the wall for 080 ms what : a pellet gun fires ten 2.9 g pellets per second with a speed of 540 ms . the pellets are stopped by a rigid wall. what

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Find the elasticity modulus 02 offset yield strength

an aluminum alloy specimen brought to tensile test had frac12 inch2 cross sectional area. it was tested to fracture and

  Describe this structure as a lattice and a basis the cu3au

consider the cuau crystal structure. it can be described as a simple cubic lattice with a basis of cu 0 0 0 cu 1 2 1 2

  You have a bevel gear and shaft and you have to find the

you have a bevel gear and shaft and you have to find the maximum load that can be applied on it. what type of

  Dtermine cycle efficiency determine mass flow rate of the

steam powerplant produces 200 mw power. saturated steam exits boiler at 3mpa pressure. turbine exits 10kpa pressure.

  Name any incongruent melting intermediate compound

(i) Name any incongruent melting intermediate compound(s) present. (j) Locate and draw a square around all congruent melting equilibria. (k) Label all the two-phase fields. (l) Is either Ti or Ni allotropic?

  A hollow 6 ft diameter sphere floats half-submerged in

a hollow 6 ft. diameter sphere floats half-submerged in seawater. what mass of concrete is required as an external

  What is happening to the entropy of the potato when it

a potato is baked in an oven at 200degc. the potato is then removed from the oven and put on a table in the kitchen.

  What is the speed of each star at the moment of impact

Gravitational forces pull the two stars together. What is the speed of each star at the moment of impact?

  Estimate the speed and mach number of the jet

While jogging on the beach (it's a warm summer day, about 30 deg C) a high-speed jet flies overhead. You guesstimate it's an altitude of about 3500 m, and count off about 5 s before you hear it. Estimate the speed and Mach number of the jet.

  Specify a diameter d using a design factor of nd

xerted on the shaft shown in the figure, which rotates at 1150 rev/min and supports a 10-kip bending force. Use a 1095 HR steel. Specify a diameter d using a design factor of nd = 1.6 for a life of 3 min. The surfaces are machined.

  Briefly explain a why there may be significant scatter in

briefly explain a why there may be significant scatter in the fracture strength for some given ceramic material and b

  What is the work produced kjkg during the expansion process

carbon dioxide is expanded in a steady flow frictionless process through a turbine from 0.9 mpa to 0.1 mpa. the initial

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd