The initial pressure is 39kpa and the initial temperature

Assignment Help Mechanical Engineering
Reference no: EM13627547

Natural gas is a mixture of methane , ethane , propane and butane as well as other components . Comsider natural gas, modeled as an ideal gas with an equivalent molecular weight 23.6kg/kmol and an equivalent constant specific heat 2.01 kJ/kg*K. The gas is slowly compressed in a frictionless , adiabatic process with initial volume 212 cm^3 to a final volume 98 cm^3. The initial pressure is 39kPa and the initial temperature is 15 deg celcius. Find the final temperature, pressure of the gas and find the work done to compress the gas.

Reference no: EM13627547

Questions Cloud

How large of a sample is needed to find the population mean : families usa a monthly magazine that discusses issues related to health and health costs surveyed 20 of its
The suspension of an automobile can be approximately by the : the suspension of an automobile can be approximately by the simplified spring-dashpot determine and plot the amplitude
A charge of 7 nc is uniformly distributed around a ring of : a charge of 7 nc is uniformly distributed around a ring of radius 10 cm that has its center at the origin and its axis
A four-cylinder engine with a 95-cm bore and an 875-cm : a four-cylinder engine with a 9.5-cm bore and an 8.75-cm stroke has a 7 clearance. the engine rotates at 2500 rpm. the
The initial pressure is 39kpa and the initial temperature : natural gas is a mixture of methane ethane propane and butane as well as other components . comsider natural gas
An infinitely long cylinder of radius 40 cm carries a : an infinitely long cylinder of radius 4.0 cm carries a uniform volume charge density r 200 ncm3. what is the electric
Consider two point particles that have charge e are at rest : consider two point particles that have charge e are at rest and are separated by 3.70 x 10-15 m.a how much work was
The american restaurant association collected information : the american restaurant association collected information on the number of meals eaten outside the home per week by
Consider two point particles that have charge e are at rest : consider two point particles that have charge e are at rest and are separated by 3.70 x 10-15 m.a how much work was

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The temperature at the end of the isentropic expansion

the compression ratio of an air-standard ideal otto cycle is 10. prior to the isentropic compression process the air is

  Find alpha the angular acceleration

Note that the positive y direction is downward and counterclockwise torques are positive. find alpha the angular acceleration?

  The ram of a pile driver has a mass of 800 kg and is

the ram of a pile driver has a mass of 800 kg and is released from rest 2 meters above the top of a 2400 kg pile. the

  The ratio of the exit area to the inlet is 8 assuming the

air enters an adiabatic diffuser operating at steady state at 540 degrees r with a velocity of 600 fts and exits with a

  The two sides of a v-shaped water trough are hinged to each

the two sides of a v-shaped water trough are hinged to each other at the bottom where they meet as shown in figure q1

  Find the initial volume and final volume for this process

five kilograms of water vapor initially at 160 c and 3 bar are cooled at constant pressure until the quality is 0.4.a

  Define steam is cooled at constant pressure until one-half

A piston-cylinder device contains 0.8kg of steam at 300 degrees C and 1 MPa. Steam is cooled at constant pressure until one-half of the mass condenses.

  The total pressure of air entering a single-stage

the total pressure of air entering a single-stage centrifugal compressor is 1.013 bar and the total t is 288 k. the

  Vital information about pressure cooker

Important information about Pressure Cooker, Steam is leaving a pressure cooker whose operating pressure is 30 psi. It is observed that the amount of liquid in the cooker has decreased by 0.4 gal in 45 minutes after the steady operating conditions..

  T plates is f q deltav 2d where deltav v2-v1 is the

a particle of mass m kg carrying q coulombs enters the space between two charged plates with the horizontal velocity

  Samples i want a unique version of this

i want a unique version of this

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd