The heat of melting for water is 155 btulbm assum that all

Assignment Help Mechanical Engineering
Reference no: EM13637205

A 2-kg block of ice with an initial temperature of -20F is dropped into an insulated tank containing 10-kg of liquid water at an initial temperature of 70F. The specific heat of the solid ice is 0.477 Btu/(lbm*F), and the specific heat of the liquid water is 1.00 Btu/(lbm*F). The heat of melting for water is 155 Btu/lbm. Assum that all of these quantities are independent of temperature.

a) Determine the final phase of the water in the tank.
b) Calculate the final temperature (F) of the water in the tank.

Reference no: EM13637205

Questions Cloud

Business organisation write an explanatory note on otcei : write an explanatory note on otcei. discuss the reason for the direct participation of government in business and
Business organisation write an explanatory note on otcei : write an explanatory note on otcei. discuss the reason for the direct participation of government in business and
A major chain of food stores wants to determine the : a major chain of food stores wants to determine the proportion of customers who buy on impulse. the company decided to
Write a problem which requries the reader to calculate : write a problem which requries the reader to calculate standard scores also called a z-scores and use these to find
The heat of melting for water is 155 btulbm assum that all : a 2-kg block of ice with an initial temperature of -20f is dropped into an insulated tank containing 10-kg of liquid
A major chain of food stores wants to determine the : a major chain of food stores wants to determine the proportion of customers who buy on impulse. the company decided to
Use constant specific heat at 300k and find the compression : a gasoline engine takes air in at 290k 90kpa and then compresses it. the combustion adds 1000 kjkg of heat to the air
A man with a mass of 60 kg steps into powdery snow and : a man with a mass of 60 kg steps into powdery snow and sinks to his waist. the area of each mans feet is 250
Find the compression ratio and the mean effective pressure : an otto cycle has the lowest temperature of 60degreef and the lowest p as 12psi. the highest temperature is 4040degreef

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Find the stresses in a point of a rod that is fixed

find the stresses in a point of a rod that is fixed to a wall and have a load in the edge or better known as a cantilever.

  Air enters an evaporative cooler at 95 kpa 35 degrees

air enters an evaporative cooler at 95 kpa 35 degrees celcius and 30 relative humidity and exits saturated. determine

  An insulated mixing chamber receives 4 lbms r-134a at 150

an insulated mixing chamber receives 4 lbms r-134a at 150 lbfin.2 220 f in a line with low velocity. another line with

  A heat engine absorbes 25 mw from a 400 c combustion

a heat engine absorbes 25 mw from a 400 c combustion chamber and rejects 15 mw to the atmosphere at 30 c. find the

  Calculate the speed at which the ball leaves the spring

A small steel ball bearing with a mass of 13 g is on a short compressed spring. When aimed vertically and suddenly released, the spring sends the bearing to a height of 1.35 m. Calculate the speed at which the ball leaves the spring.

  Control engineeringyou have to design a control system for

control engineeringyou have to design a control system for an annealing furnace. the furnace is used to anneal special

  What electric output would you estimate for this electric

a gas turbine can assume an ideal brayton cycle has a pressure ratio of 10. it is connected to an electric generator

  The power output of the two-stage turbine is 80 mw and

steam enters a two-stage adiabatic turbine at 8 mpa and 550ordmc state 1 and is expanded to 2 mpa state 2 in the first

  A train made up of 3 cars of weight 60000 lb each connected

a train made up of 3 cars of weight 60000 lb each connected by coupling springs of stiffness 15000 lbin. is released by

  An engine of mass 180 kg is to be supported on four helical

an engine of mass 180 kg is to be supported on four helical springs. when the engine speed is 900 rpm there is a

  Determine the difference between these values and the

an airplane flying at m0 0.8 under standard sea level conditions has instrumentation embedded at the stagnation point

  A steam power plant operates with a boiler output of 20 kgs

a steam power plant operates with a boiler output of 20 kgs steam at 2 mpa 600degc. the condenser operates at 50degc

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd