The flywheel of a small punching machine rotates at 360 rpm

Assignment Help Mechanical Engineering
Reference no: EM13627334

The flywheel of a small punching machine rotates at 360 rpm. Each punching operation requires 1500 ft-lb of work and it is desired that the speed of the flywheel after each punching be not less than 95 percent of the original speed.

A) Determine the required moment of inertia of the flywheel.

B) If a constanc 18 lbft couple is applied to the shaft of the flywheel, determine the number of revolutions that must occur between two successive punchings, knowing that the initial velocity is to be 360 rpm at the start of each punching.

Reference no: EM13627334

Questions Cloud

Sketch not to scale the variation of shear stress vs shear : sketch the variation of shear stress vs shear strainnot to scale along the radius in a composite bar of total radius r
Find the maximum and minimum transmittance of the : the plates of a fabry-perot interferometer are coated with silver of such a thickness that for each plate the
The storage tank of a water tower is a vertical cylinder of : the storage tank of a water tower is a vertical cylinder of diameter d 7 m the initial depth of water within it is ho
Assuming the piano strong has too low a pitch what percent : a piano tuner hears a beat frequency of 6.2 hz when comparing the pianos a-string against a reference tuning fork
The flywheel of a small punching machine rotates at 360 rpm : the flywheel of a small punching machine rotates at 360 rpm. each punching operation requires 1500 ft-lb of work and it
If the score recorded in the grade book is the total number : an instructor has given a short quiz consisting of two parts. for a randomly selected student let x the number of
How long does an organ pipe have to be if it is closed at : how long does an organ pipe have to be if it is closed at one end open at the other and has a fundamental frequency of
If they go back and revise their answers they start second : when taking an exam some students quickly answer all the questions they know how to do. if they go back and revise
A hydrogen atom undergoes a transition from the n 12 state : a hydrogen atom undergoes a transition from the n 12 state to the n 5 state. during this transition does the atom

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  If the reading on the pressure gage is 80 kpa determine the

both a gage and a manometer are attached to a gas tank to measure its pressure. if the reading on the pressure gage is

  Now heat is transferred to the refridgerant -134a until the

a piston-cylinder device contains 0542 kg of refridgerant -134a at -10 degrees c. the piston is free to move has a mass

  Determine the number of bolts needed

A lap joint needs to be designed using 20-mm diameter bolts to carry a load of 120 kN on the connecting plates. If the shear stress in each rivet is not to exceed 90 MPa, determine the number of bolts needed.

  What is the probability of choosing any one random

best buy gives a choice of 3 cpu models 2 monitors 3 printers and 2 scanners. they can operate in any combination. in

  Determine the stream ecomomy of the system assume that the

feed at 10 ccelsius containing 20 solids enters an evaporator operating at 90 ccelsius. saturated steam90 quality

  Determine the normal stress in the central portion of link

the link DE is 3mm thick and 25 mm width,determine the normal stress in the central portion of the link.

  Determine the natural frecuency of the automobile

an automobile having a mass of 2000 kg deflects its suspension springs 0.02 m under static conditions. Determine the natural frecuency of the automobile in the vertical direction by assuming dumping to be negligible.

  How much work was done on the roof by the forces

In 1975 the roof of Montreal's Velodrome, with a weight of 360 kN, was lifted by 10 cm so that it could be centered. How much work was done on the roof by the forces making the lift?

  An air compressor takes air from outdoors at 28deg c and

an air compressor takes air from outdoors at 28deg c and 101.2kpa and compresses it to 790kpa and 50 deg c. the air

  Calculate the acceleration in ms2 with which the iron ball

an iron ball is thrown into the atlantic ocean. density of iron is 7856 kgm3. density of salt water is 1020 kgm3.

  Hot isostatic pressing hiping should make these products

cast aluminum products often contain gas porosity and shrinkage cavities which can undermine the integrity of these

  An engine block with a surface area measured to be 090m2

an engine block with a surface area measured to be 0.90m2 generates a power output of 55 kw with a net engine

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd