The final pressure is 3 bar find the final temperature and

Assignment Help Mechanical Engineering
Reference no: EM13624894

SIX kg of STEAM and TEN kg of LIQUID H2O are sealed in a rigid device with an internal-piston-cylinder. Both are at rest at the temperatures shown and the same initial pressure of 10 bar. External heat transfer allows the temperature and pressure to fall.The rigid piston moves freely (without friction) and conducts heat from the hot gas to the cold gas. The mass and energy of the piston material are negligible. The final pressure is 3 bar. Find the final temperature and total heat transfer for the process to reach thermal equilibrium with a single uniform temperature H2O SHB m=6kg T1=600C H2O Liq m=10kg T1=100C.

Reference no: EM13624894

Questions Cloud

Chebyshevs inequality for regular worker the preparation : chebyshevs inequality for regular worker the preparation time for daily work needs 35 minutesday and with standard
What is the difference between standard normal distribution : what is the difference between standard normal distribution and t-distribution?could anyone help me this
Two kg of saturated liquid water at 1 bar is compressed to : two kg of saturated liquid water at 1 bar is compressed to 25 bar and 100degc in a water pump. determine the change in
The convection heat transfer coefficient is 100 wm2k if the : to defog the rear window of an automobile a very thin transparent heating element is attached to the inner surface of
The final pressure is 3 bar find the final temperature and : six kg of steam and ten kg of liquid h2o are sealed in a rigid device with an internal-piston-cylinder. both are at
A die with 6 facts but only marked two facets with 1 and : a die with 6 facts but only marked two facets with 1 and rest 4 facets with 2 if we throw this die 60 times we expect
The water is rapidly stirred until the pressure equals 40 : a well-insulated rigid tank has a volume of 10ft3 water with a quality of 0.7 at 212of. the water is rapidly stirred
Models of management why is it important for organizations : why is it important for organizations in india to search for hybrid improvised models of
Determine the rate of heat supply in the boiler the rate of : the turbine of a steam power plant operating on a simple ideal rankine cycle produces 500kw of power when the boiler is

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Prepare the project objectives based on the requirement out

prepare the project objectives based on the requirement out lined at the next page.the following is the project

  How much does it save in gasoline if compared to a 30

the hybrid vehicle engine produces an average of 25 kw of power output and has an efficiency of 65. assume it runs 200

  Estimate how fast should the container accelerate in order

the 0.5m long container shown in the figure accelerates downhill 25 degrees to horizon so that the liquid surface is

  It takes an airbus roughly 75 seconds to get to that

an airbus 310a with a mass of 140000 kg sits on a runway. it takes off and flies to an altitude of 10500 m with a speed

  Air flows in a channel whose velocity at 3 neighbouring

air flows in a channel whose velocity at 3 neighbouring points ab and c which are 10 cm apart are shown in the

  What is the acceleration of the center of disk

What is the magnitude of the friction force between the ramp and the cylindrical disk?

  Determine the acceleration a of the car just after passing

a car is climbing the hill of slope theta1 at a constant speed v. if the slope decreases abruptly to theta2 at point a

  Find the tension in each rope

260-pound weight is supported by two ropes, one forming a 40 degree angle with the ceiling and the other a 50 degree. Find the tension in each rope.

  If the enthalpy of feedwater is 215 kjkg and the enthalpy

pressurized feedwater in a steam power plant is to be heated in an ideal open feedwater heater that operates at a

  A gymnast of weight 720n is holding himself in the cross

a gymnast of weight 720n is holding himself in the cross position on the high rings. he is quite still. draw a

  The lift coefficient at this speed is 045 and the drag

an aircraft is in level flight at 225 kmhr through air at standard conditions. the lift coefficient at this speed is

  Estimate the mass flow rate of fuel into the engine

Estimate the mass flow rate of fuel into the engine in kg/h.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd