The fin array is exposed to air at tair 20 degrees c with

Assignment Help Mechanical Engineering
Reference no: EM13630016

A fin array consists of 6 rectangular fins on a 2mm thick, 100mm by 180mm plate. The array is made of aluminum, and each fin is 30 mm long and 2mm thick. The array is attached to the surface of an electronics enclosure. The contact resistance between the surface of the enclosure and teh fin array is Rt,c = 5 X 10^-4 m^2 K/W.

The fin array is exposed to air at Tair = 20 degrees C with a convection coefficient of h = 40 W/m^2 K, and the fin array dissipates 130 W of heat to the convection enviroment.

Reference no: EM13630016

Questions Cloud

Determine the following assume that the tunnel operates : a hypersonic gun tunnel is used to generate short-duration high-speed flows and typically consists of two cylindrical
What is the force exerted by the seat on the child at the : a 42.0 kg child sits in a swing supported by two chains each 3.06 m long.a if the tension in each chain at the lowest
Calculate by hands report the chi-square statistic degrees : a researcher is interested in the relationship between birth order and personality. a sample of n100 people is obtained
An 1820 kg car passes over a bump in a road that follows : an 1820 kg car passes over a bump in a road that follows the arc of a circle of radius 41.9 m.a what force does the
The fin array is exposed to air at tair 20 degrees c with : a fin array consists of 6 rectangular fins on a 2mm thick 100mm by 180mm plate. the array is made of aluminum and each
Define the physical uncontrolled seat including seat : a farm equipment manufacturer has a need to actively reduce the vibration of the operators seat using an electrodynamic
The dog starts running when the owners are d 80 m apart if : a dog runs back and forth between its two owners who are walking toward one another. the dog starts running when the
A tank fitted with an electrical resistor holds 2 kg of : a tank fitted with an electrical resistor holds 2 kg of nitrogen n2 initially at 1 bar. over a period of 10 minutes
A cheetah can accelerate from rest to 220 ms in 676 s a : a cheetah can accelerate from rest to 22.0 ms in 6.76 s.a assuming constant acceleration how far has the cheetah run in

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The refrigerant leaves the condenser at 07 mpa 26 degc

consider a non-ideal vapor-compression cycle where refrigerant 134a flows at a rate of 0.05 kgs. the refrigerant enters

  What is the speed a pararescuer enters the water following

coast guard pararescue jumpers are trained to leap from helicopters into the sea to save boaters in distress. the

  Steam contained within a piston-cylinder assembly undergoes

1 given nitrogen n2 gas within a piston-cylinder assembly undergoes a compression from p1 0.2 mpa v1 2.75 m3 to a

  Find the natural frequency

Three springs anda mass are attached to a rigid, weightless bar PQ hinged at one end. How do I find the natural frequency?

  Explain the distortion energy failure theory

How do I find the factor of safety using the distortion energy failure theory?

  Specify a diameter d using a design factor of nd

xerted on the shaft shown in the figure, which rotates at 1150 rev/min and supports a 10-kip bending force. Use a 1095 HR steel. Specify a diameter d using a design factor of nd = 1.6 for a life of 3 min. The surfaces are machined.

  What is the volume occupied by the water vapor what is the

a frictionless piston-cylinder is filled with 3 liters of water at 250 kpa. initially the temperature of the water is

  Find the derivative of the following function using

find the derivative of the following function.y5cos10xx3-2x2-6x10using backward difference and central difference

  An ideal gas at 100 kpa and 15 degrees c enters a

an ideal gas at 100 kpa and 15 degrees c enters a steady-flow compressor. the gas is compressed to 600 kpa and 10 of

  Determine the largest load which can be applied knowing

a block of 10-in length and 1.8 times 1.6 in. cross section is to support a centric compressive load p. the material to

  When a 2000 lb vehicle is empty the static deflection of

when a 2000 lb vehicle is empty the static deflection of its suspen- sion system is measured as 0.8 in. what is the

  What are the forces acting on workpiece

What are the forces acting on workpiece during turning process. how workpiece should be clamp

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd