User Account

All Pages

The facility is required to collect all the vented air and

Assignment Help Mechanical Engineering
Reference no: EM13633416

An alcohol manufacturing facility emits air with 500 ppm ethanol. The air flows out several roof vents at a total flow rate of 1000 m³/min (at 25 ° C and 1 atm). The facility is required to collect all the vented air and route it to a biofilter to control total emissions to less than 30 kg of ethanol per day. Calculate the required control efficiency.

Reference no: EM13633416

Questions Cloud

If an open-tube manometer is open to the atmosphere 760 : if an open-tube manometer is open to the atmosphere 760 torr themercury levels are equal. what is the pressure in the
If the slope of this line is 0675 and the y-intercept is : a a steel made up of 100 martensite is completely tempered to give an equilibrium composition consisting of 85 wt
A hydraulic press consists of two vertical cylinders of : a hydraulic press consists of two vertical cylinders of circular cross-sectional areas 6cm2 and 120cm2 that are joined
Calculate the approximate alkalinity milligrams per : calculate the approximate alkalinity milligrams per litercaco3 for water containing 120 mgl of bicarbonate ionand 15
The facility is required to collect all the vented air and : an alcohol manufacturing facility emits air with 500 ppm ethanol. the air flows out several roof vents at a total flow
A point charge of -15 c is located at the origin a second : a point charge of -1.5 c is located at the origin. a second point charge of 10 c is at x 1 m y 0.5 m. find the x and
In the hall-heroult process anhydrous aluminum oxide : in the hall-heroult process anhydrous aluminum oxide isreduced to aluminum according to the chemical equation 2al2o3 s
Indirect labor andother overhead is calculated simply at a : 1. operators assemble pumps at an hourly rate of 10.00.the standard time for the assembly is 20minutes. direct material
A proton is located at the origin and a second proton is : a proton is located at the origin and a second proton is located on the x-axis at x 5.38 fm 1 fm 10-15 m.a calculate

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the maximum torque t

a shaft is made of a steel alloy having an allowable shear stress of 12 ksi. If the diameter of the shaft is 1.5 in., determine the maximum torque T that can be transmitted. What would be the maximum torque T' if a 1 in. diameter hole is bored thr..

  Find the final pressure in the cylinder determine the heat

five lbm of water 60 degree f is contained in a vertical cylinder by a frictionless piston of a mass such that the

  A turbine is supplied with 6m3s of water from a 3-m

a turbine is supplied with .6m3s of water from a .3-m diameter pipe the discharge pipe has a .4m diameter. determine

  A j type thermocouple referenced at 70f has a measured emf

a j type thermocouple referenced at 70f has a measured emf of 2.878mv. what is the tempature of the measured

  Air flows at 120degc in a thin-wall stainless-steel tube

air flows at 120degc in a thin-wall stainless-steel tube with h 65 wm2 middot degc. the inside diameter of the tube is

  The drum rolls without slipping on the surface of the

a drum rools on a conveyor with is moving at a constant velocity of 3fts. the drum rolls without slipping on the

  A hydraulic cylinder has a piston of cross sectional area

a hydraulic cylinder has a piston of cross sectional area 45cm2 and a constant working fluid pressure of 2.2mpa. the

  Evaluate the maximum height reached by the sphere

Evaluate the maximum height reached by the sphere, and the distance traveled by the block.

  Assume and then justify that the sphere between as a

the heat transfer coefficient for air flowing over a sphere is to be determined by observing the temperature -time

  What is the atmospheric pressure at that altitude if the

a pilot flying a new airplane reports that she is flying at 49000 ft as read on her altimeter that is referenced to

  At the beginning of the compression process p11bar and

he compressor ratio of an air standard otto cycle is 8. at the beginning of the compression process p11bar and t1300k.

  Determine the velocity and pressure profiles

Given an aerodynamic body, you have learned in Aerodynamics and Flight Mechanics how to apply the numerical Source Panel Method to this body to determine the velocity and pressure profiles along the surface of the body.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd