The exhaust from a natural gas heating is expelling

Assignment Help Mechanical Engineering
Reference no: EM13643413

The exhaust from a natural gas heating is expelling combustion products at a rate of 10 mole per minute. On a mass basis, the exhaust gas contains 10% water, 70% CO2, 10% O2 and 10% CO. The molecular mass of these species are 18,44,32,28 g/mol respectively.

1. What is the composition of the flue gas in mole percentage
2. How much water leaves the exhaust gas in grams per minute
3. If for some reason, all the water condenses in the side of the flue stack, what would be the composition of the flue gas on a mass percentage basis.

Reference no: EM13643413

Questions Cloud

The balls have a glancing collision not a head-on collision : one billiard ball is shot east at 2.15 ms. a second identical billiard ball is shot west at 1.42 ms. the balls have a
What minimum mass of succimer in is needed to bind all of : what minimum mass of succimer in is needed to bind all of the lead in a patients bloodstream? assume that patient
If the water has an initial temperature of 25 degrees : a pot full of water 4l is to be placed on a stove until it boils. the stove element puts 2500w into the water in the
The cold reservoir for this plant is a pool of water : imagine that a site in iceland is discovered where temperatures a relatively short distance below the surface of the
The exhaust from a natural gas heating is expelling : the exhaust from a natural gas heating is expelling combustion products at a rate of 10 mole per minute. on a mass
What is the maximum electric power that could be produced : imagine a solar electric power plant that operates by using a gigantic mirror to concentrate light on the boiler for a
The plant generates 20mw of electricity and uses coal with : a power plant has an overall efficiency of 30. the plant generates 20mw of electricity and uses coal with a heating
A 3-g bullet flying at 420 ms hits a 22-kg aluminum block : a 3-g bullet flying at 420 ms hits a 2.2-kg aluminum block and embeds itself in the aluminum. after everything has come
Using data tables and the answer to a calculate hdegf for : a sample of sucrose c12h22o11 weighing 0.1265 g is burned in a bomb calorimeter. after the reaction is over it is found

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Consider the figure below which shows the energy-band

question 1consider the figure below which shows the energy-band splitting of silicon. if the equilibrium lattice

  Show the cycle on at p-v and t-s diagrams calculate the net

an air standard cycle with variable specific heats is executed in a closed system and is composed of the following four

  The coefficient of compressibility is 80 x10-7 atm-1

the molar volume of al2o3 at 25 degrees celsius and 1 atm is 25.715 ccmol. its coefficient of thermal expansion is 26

  100kpa and 22 degc air is contained in a rigid tank of 2 m3

100kpa and 22 degc air is contained in a rigid tank of 2 m3. there is supply line connected to the tank through a

  A gas is contained in a vertical fractionless- cylinder

a gas is contained in a vertical fractionless- cylinder device. the piston has a mass of 4 kg and cross sectional area

  The air and co behave as ideal gases with constant specific

2 kg of air initially at 5 bar 350 k and 4 kg of carbon monoxide initially at 2 bar 450 k are confined to opposite

  It is estimated that the refrigerator removes 3300 kjhr

1. a commercial refrigerator keeps food fresh at -12 ordmc. it is estimated that the refrigerator removes 3300 kjhr

  How did you do the maintenance during your workshop

Show how did you do the maintenance during your workshop

  What is the solar flux absorbed by the abdorber plate given

a solar collector is made of a cover plate then a 5 cm air gap and then an absorber plate with insulation on the back

  Run a fmea analysis and suggest the possible solution

The plate fin heat exchanger uses gaskets to separate oil and water paths. Since this unit is used in trucks, vibration should also be considered. Run a FMEA analysis and suggest the possible solution to avoid future failure.

  Te rate of energy transfer by convection from the

electronic components mouted on a flat plate are cooled by convection to the surroundings and by liquied water

  What can be said about the expected defect rate

Given that the nominal diameter (per print) is 15.00mm +/-0.10mm, what can be said about the expected defect rate?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd