The emission of an air pollutant is often influenced more

Assignment Help Mechanical Engineering
Reference no: EM13625217

The emission of an air pollutant is often influenced more by reaction kinetics than by chemical equilibrium. Verify whether this is true for a hypothetical case of hydrocarbon (methane) combustion. The pseudo-first-order rates of the relevant parallel reactions can be represented as follows:

CH4 + 1.5O2 = CO + 2H2O k1 (s-1) = 0.5x108 exp(-20000/T)
CH4 + 2O2 = CO2 + 2H2O k2 (s-1) = 1.0x106 exp(-15000/T)

Compare the equilibrium composition with the composition achieved after burning 50 mol/L of CH4 for 1 s at 950 K and 1 atm air. And for 20 s?

Hints: (a) Solve three equations in three unknowns, [CH4], [CO], [CO2], to determine the kinetics-governed composition. (b) Remember that conductances (rate constants) are additive for simultaneous processes (reactions).

Reference no: EM13625217

Questions Cloud

Rank the periods of the following oscillating systems from : a block with mass m 0.4 kg oscillates with amplitude a 0.4 m at the end of a spring with force constant k 7 nm on a
The potential for air pollution by particulate matter pm25 : the potential for air pollution by particulate matter pm2.5 andor pm10 is best assessed by constructing the terminal
The final pressure in cylinder reaches 200 kpa after the : consider a pistoncylinder arrangement that has a linear spring mounted such that as the piston rises to a certain point
The frequency of vibration of a lithotriptor an ultrasound : the frequency of vibration of a lithotriptor an ultrasound generator used to destroy kidney stones is 1.1 mhz.a what is
The emission of an air pollutant is often influenced more : the emission of an air pollutant is often influenced more by reaction kinetics than by chemical equilibrium. verify
Which of the following methods could lead to stronger : which of the following methods could lead to stronger evidence for the outcome of a nonparametric test?a. ensure that
A electron with kinetic energy 490 kev circles in a plane : an electron with kinetic energy 4.90 kev circles in a plane perpendicular to a uniform magnetic field. the orbit radius
The final pressure is 14 mpa determine the work and the : a pistoncylinder arrangement is filled with helium gas. the gas is compressed with a polytropic process with nk. the
A mechanical engineer who recently graduated with a masters : a mechanical engineer who recently graduated with a masters degree is contemplating starting his own commercial heating

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Prove using the increse in entropy principle that the

a prove using the increse in entropy principle that the maximum thermal efficiency for any heat engine is the carnot

  Determine the flow rate of stream and the thermal efficiency

an ideal rankine cycle produces 100 MW of power. If the steam enters the turbine at 100 bar and 500C and is condensed at 1 bar, determine the flow rate of stream and the thermal efficiency.

  Derive the governing equilibrium equation in terms of

the bar in the picture is subjected to a distributed force fx and tensile forces at the both ends. derive the governing

  Estimate the true strain epsilonzz at the base of the

a circular cylinder of tantalum with an initial diameter of 3.1 mm is fired at a target. during impact the base of the

  The inefficiencies of engine components determine the force

consider an aircraft powered by a turbojet engine that has a pressure ratio of 9. the aircraft is stationary on the

  You think this is a polytropic compression process write

you are a new engineer at a company that manufactures gas-filled shock absorbers for racing cars. the chief engineer

  Determine the two inlet mass flows needed to meet

The heating is to be done in a mixing tank by direct injection of the steam, all of which condenses. Determine the two inlet mass flows needed to meet the desired hot water flow rate.

  The barometer reads 2973 inches hg and the stagnation

a pitot static tube records a static pressure of 5.20 psig and a difference between impact pressure and static pressure

  Determine the required length l

Determine the required length L of each splice if a factor of safety is 2.75.

  Determine the number of storage bits required in the control

Determine the number of storage bits required in the controller memory so that the accuracy of the joint is as close as possible to, but less than, its repeatability. Use six standard deviations as the measure of repeatability.

  The baseball player a hits the baseball with va 40 fts and

the baseball player a hits the baseball with va 40 fts and thetaa 52circ. when the ball is directly above of player b

  During the expansion some of the water evaporates but no

ten grams of liquid water at 95 c are contained in the insulated container shown. the pin holding the frictionless

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd