The density of liquid oxygen at 95 k is around 500 kgm3 if

Assignment Help Mechanical Engineering
Reference no: EM13613220

Liquid oxygen is stored in a thin-walled, spherical container 0.8 m in diameter, which is enclosed within a second thin-walled, spherical container 1.2 m in diameter. All surfaces are opaque, diffuse, and gray, and have a total hemispherical emissivity of 0.05. Both surfaces are separated by an evacuated space. If the outer surface is at 280 K and the inner surface is at 95 K, what is the mass rate of oxygen lost due to evaporation? Based on this mass rate of oxygen lost, how much is the liquid oxygen left in the container after 24 hours? The latent heat of vaporization of oxygen is 2.13 x 105 J/kg. The density of liquid oxygen at 95 K is around 500 kg/m3 . If the emissivity is increased to 0.9, do you think the evaporation rate will decrease or increase?

Reference no: EM13613220

Questions Cloud

Prepare journal entries to record the following selected : prepare journal entries to record the following selected transactions of calio co. mar 21 accepted a 17200 180-day 7
Determine a the maximum temperatureand pressure that occur : an ideal otto cycle has a compression ratio of 8. at the beginning of the compression process air is at 100kpa and
A 90 microf capacitor is charged by a 140 v battery through : a 9.0 microf capacitor is charged by a 14.0 v battery through a resistance r. the capacitor reaches a potential
Cyclone rentals borrowed 15550 from a bank for three years : cyclone rentals borrowed 15550 from a bank for three years. if the quoted rate apr is 8.83 percent and the compounding
The density of liquid oxygen at 95 k is around 500 kgm3 if : liquid oxygen is stored in a thin-walled spherical container 0.8 m in diameter which is enclosed within a second
Kevin winthrop is saving for an australian vacation in : kevin winthrop is saving for an australian vacation in three years. he estimates that he will need 4352 to cover his
A hiker walks 531 degrees north of east for 25km then due : a hiker walks 53.1 degrees north of east for 2.5km then due east for 2.0km. what is her total displacement from her
Modern energy company owns several gas stations management : modern energy company owns several gas stations. management is looking to open a new station in the western suburbs of
The power output of the heat engine is 180 kw determine the : a heat engine receives heat from a source at 1200 k at a rate of 500 kjs and rejects the waste heat to a medium at 300

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A fixed quantity of air at t1 60oc and p1 158 kpa is

a fixed quantity of air at t1 60oc and p1 158 kpa is heated at constant temperature in a piston-cylinder assembly

  How to calculate the adiabatic flame temperatures

how to calculate the adiabatic flame temperatures from the injection pressures during choked conditions.

  Problem a tension link shown to the right is used in

problem a tension link shown to the right is used in earth-moving equipment and is subjected to cyclic stresses varying

  Calculate a the work produced by the turbine per unit mass

a turbine that is well insulated runs on air. at steady state air enters at 0.5 mpa and 727 c and expands

  Determine the breaking force ff at each front wheel and the

during a break test the front wheel drive car is stopped from an initial speed of 60 mihr in 175 ft. if it known that

  Determine the ideal launch vehicle

Determine the ideal launch vehicle that can put this orbiter into the parking orbit. (hint: you do not have to consider the Sun in this problem. Only SOI of the Earth and the Moon)

  Draw the projections of rod showing curves of intersection

A connection of rod of 50 mm diameter has a rectangular block 50 mm wide and 25mm thick forged at its end. A turned radius of 25 mm joins the rod and the block. Draw the projections of the rod showing curves of intersection.

  Heat transfer to the cylinder causes an isothermal

a piston-cylinder with a volume of 0.5 m3 holds 1 kg of nitrogen at a temperature of 261 k. heat transfer to the

  Estimate the design-stage uncertainty in determining the

estimate the design-stage uncertainty in determining the voltage drop across an electric heating element. the heater

  Find the boundary work done by the mass

Consider a mass going through a polytropic process where pressure is directly proportional to volume (n=-1) the process starts with P=0,V=0 and ends with P=600kPa,V=0.01m^3. Find the boundary work done by the mass.

  Preparing cad geometry for fea

Demonstrate suitable accuracy by using a simple hand calculation for the static analysis of the structure. Describe in detail the hand calculations performed to validate the final solution. What is the approximate error between the simplified hand..

  What must be its minimum yield strength

A steel alloy to be used for a spring application must have a modulus of resilience of at least 2.07 MPa (300 psi). What must be its minimum yield strength?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd