The crankshaft in a given automobile rotates

Assignment Help Mechanical Engineering
Reference no: EM13713187

The crankshaft in a given automobile rotates, on average, at 2500 revolutions per minute for a period of 2 h per day. How long would it take before the crankshaft has been subjected to 10^8 load cycles?

Reference no: EM13713187

Questions Cloud

Identify parameters : Read (a,b,c); if(a!=0){d=b*b-4*a*c;if(d
What is the angular velocity of the bicycle : A bicyclist starts at rest at the top of a 50.3m long hill. After a small push, he coasts speeding up with an acceleration of 3.43m/s2 due to the slope of the hill. What is the angular velocity of the bicycle tires at the bottom of the hill.
Electrical work is employed to heat : Electrical work is employed to heat 2kg of water from 298.15 K to 373.15 K. Determine the electrical work required, and the minimum work required (e.g., by using a heat pump instead).
Write a summary of the book born to buy : You need to write a summary of the book born to buy.
The crankshaft in a given automobile rotates : The crankshaft in a given automobile rotates, on average, at 2500 revolutions per minute for a period of 2 h per day. How long would it take before the crankshaft has been subjected to 10^8 load cycles?
Energy conservation and availability balance equation : Water vapor at 300 C, 35 bars (state 1) expands to 5.0 bars (state 2) using an adiabatic throttling valve. The ambient is at T = 25 C, 1 bar. Simplify the energy conservation and availability balance equation for the current problem. Calculate the ex..
What is the internal resistance of the battery : A battery has an emf of 15.0 V. The terminal voltage of the battery is 13.4 V when it is delivering 16.0 W of power to an external load resistor R. What is the internal resistance of the battery.
Landing gear on a commercial aircraft experiences : The landing gear on a commercial aircraft experiences an impulse load upon landing. Assuming seven such landings per day on average, how long would it take before the landing gear has been subjected to 108 load cycles? (Answer in years)
Same mass is added through both inlets : An initially empty, well insulated, rigid tank with a volume of 2 m^3 is fitted with a mixing device. The tank has two inlets and zero outlets. One inlet is water at 1.07 MPa and 630ºC while the other is saturated liquid water. Both enter the tank sl..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the average normal stress at the section a-a and

determine the average normal stress at the section a-a and the average shear stress at section b-b in member ab. the

  Determine the steady state irreversibility rate of each

the surface temperature of a 100 w incandescent lightbulb is 60.0degc. the surface temperature of a 20.0 w fluorescent

  A 50 kg crate rests on a rough horizontal surface with

a 50 kg crate rests on a rough horizontal surface with microk0.3. an electrically powered winch is utilize to

  A closed rigid vessel conatains 3 liguid water and 97

a closed rigid vessel conatains 3 liguid water and 97 water vapor by volume. the mixture is in equilbrium at 100o c.

  Determined the flame temperature of the burner

Propane is mixed 20% excess air (propane air mixture is initially at 25 C and 2.0 atm) and combusted at atmospheric pressure. It is assumed that the heat transfer between the chamber and the surroundings is negligible. In addition, you may assume tha..

  Water starts at a temperature of 19 degrees celcius and is

water starts at a temperature of 19 degrees celcius and is then boiled until it is a superheated steam at temperature

  An electric field is e400nci for xgt0 and e-400nci for xlt0

an electric field is e400nci for xgt0 and e-400nci for xlt0. a cylinder of length 30cm and radius 10cm has its center

  Gear is put in neutral on level road without wind resistance

The rolling resistance of a 1200kg car depends on its weigh as F = 0.006m x gravity. How far will the car roll if at 90km/h the gear is put in neutral on a level road without wind resistance?

  A bending moment of 3 kn-m and a torque of 5 kn-m a safety

a solid circular shaft has a diameter of 60 mm and is subjected to a tensile axial load of 200 kn a bending moment of 3

  Determine a the inital acceleration of the projectile b the

a projectile enters a resisting medium at x0 with an initial velocity of vo900fts and travels 4 inches before coming to

  An of milk at 68of is placed in a refrigerator

1 given amp find a r-134a at t 60oc and v 0.072 m3kg. find p and h.b ammonia at p 8 bar and v 0.005 m3kg. find

  Assume that the velocity v of fall of an object depends on

assume that the velocity v of fall of an object depends on the height h through which it falls the gravity g and the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd