The chain and lever attached to the gate have negligible

Assignment Help Mechanical Engineering
Reference no: EM13620507

A gate with a circular cross section is held close by a lever 1 m long attached to a buoyant cylinder. The cylinder is 25 cm in diameter and weighs 200 N. The gate is attached to a horizontal shaft so it can pivot about its center. The liquid is water. The chain and lever attached to the gate have negligible weight. Find the length of the chain such that the gate is just on the verge of opening when the water depth above the gate hinge is 10m.

Reference no: EM13620507

Questions Cloud

What is the rationale underlying the appropriateness of : an accountant must be familiar with the concepts involved in determining earnings of a company. the amount of earnings
Please show work if possible green thumb garden centers : please show work if possible green thumb garden centers sells 240000 bags of lawn fertilizer annually. the optimal
Bond x is noncallable and has 20 years to maturity a 9 : bond x is noncallable and has 20 years to maturity a 9 annual coupon and a 1000 par value. your required return on
The total degrees of freedom for an experiment with n1 10 : the total degrees of freedom for an experiment with n1 10 n2 12 and n3 10 is .1. 292. 313. 24.
The chain and lever attached to the gate have negligible : a gate with a circular cross section is held close by a lever 1 m long attached to a buoyant cylinder. the cylinder is
If r 12 cm m 370 g and m 40 g below find the speed of : if r 12 cm m 370 g and m 40 g below find the speed of the block after it has descended 50 cm starting from rest.
Your friend is considering adding one additional stock to a : your friend is considering adding one additional stock to a 3-stock portfolio to form a 4-stock portfolio. she is
What is the maximum speed of a truck that you are sure will : on a trip to the colorado rockies you notice that when the freeway goes steeply down a hill there are emergency exits
The only question is the strength of the block in : limestone blocks approximately 8 in. wide by 14 in. long by 6 in. high are sometimes used in constructing dry stacked

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the actual strain

You have a 120 Ω quarter bridge 2 wire set up with Sg=2.10 and an unknown lead wire resistance. A 59880Ω calibration resistor is switched in parallel to the gage only and a recording instrument is set to give a -100 mm deflection for this calibrat..

  Determine the angular velocity and angular acceleration

Block B of the mechanism is confined to move within the slot member CD. If AB is rotating at a constant rate of AB = 3rad/s, determine the angular velocity and angular acceleration of member CD at the instant shown.

  The specimen failed due to stress rupture after 100 hours

a new high- temperautre alloy is to be used for a 3-mm diameter tensile support member for an impact-sensistive

  Find the heat transfer and work for each component find

a geothermal heat pump is used to provide a house with 5 kw of heating. the house is at 25degc and the ground

  Coding for computerized relative allocation of facilities

How to do matlab coding for computerized relative allocation of facilities technique

  The motor of a speed boat is shut off when it has attained

the motor of a speed boat is shut off when it has attained a speed of v0. now the boat is slowed down by a retarding

  Calculate the power output in kw

Air enters a turbine at 40 kN/m2, 900 C, and leaves at 10 kN/m2. The flow is reversible and adiabatic. Inlet velocity is quite low and outlet velocity is 150 m/s through a cross-sectional area of 0.20 m2. Calculate the power output in kW.

  Develop equations which may be solved to give the final

develop equations which may be solved to give the final temperature of the gas remaining in a tank nbspafter the tank

  A value that causes the 24 hr average velocity to be 20 ms

a wind turbine with a swept area of 1000 m2 operates with 56 efficiency under stp conditions. at the location of the

  Determine the heat transfer rate through the wall for outer

a concrete wall which has a surface area of 20 m2 and is 0.30 m thick separates conditioned room air from ambient air.

  What is the minimum plate length that should be used at

a fan that can provide air speeds up to 50ms is to be used in a low-speed wind tunnel with atmospheric air at 25 degc.

  Determine the speed at which the pilot in the bomber sees

the pilot of flighter plane f is following 1.5 behind the pilot of bomber b. both planes are originally traveling at

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd