The boxs surface is the 12x36 side and the 2x2 surface is

Assignment Help Mechanical Engineering
Reference no: EM13643230

A 12"x36" and 9" high empty prism composed of a material with an Elastic modulus of 345,000 psi, 9,000 psi yield stress, the walls of the prism are 0.74" thick, and weight of 40 pounds is placed on a pedestal in which the surface that makes contact with the prism is 2"x2" , the box's surface is the 12"x36" side, and the 2"x2" surface is directly in the center of the prism. What is the stress caused on the prism by being placed on this pedestal, what are the moments if any exist.

Reference no: EM13643230

Questions Cloud

What is the temperature at the outer surface of the : a very thin and long pipeline used for the transport of crude oil is buried in the earth such that its centerline is a
At a given instant in time the forces resisting the motion : the speed of a bobsled is increasing because it has an acceleration of 2.3 ms2. at a given instant in time the forces
A pentapeptide is composed of ala cys lys phe and ser : a pentapeptide is composed of ala cys lys phe and ser. nh2-terminal analysis of the peptide revealed pth-serine.
A tuning fork vibrating at 517 hz falls from rest and : a tuning fork vibrating at 517 hz falls from rest and accelerates at 9.80 ms2. how far below the point of release is
The boxs surface is the 12x36 side and the 2x2 surface is : a 12x36 and 9 high empty prism composed of a material with an elastic modulus of 345000 psi 9000 psi yield stress the
A polypeptide is subject to the following degradative : a polypeptide is subject to the following degradative techniques resulting in polypeptide fragments with the indicated
An airplane has a mass of 34500 kg and takes off under the : an airplane has a mass of 34500 kg and takes off under the influence of a constant net force of 42500 n. what is the
The velocity of the water coming out is 075 ms calculate : a farmer in canterbury has a resource consent allowing him to use 100000l of water a day from the nearby river.
A positive charge of q1 is located 550 m to the left of a : a positive charge of q1 is located 5.50 m to the left of a negative charge -q2. the charges have different magnitudes.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The water enters the electric heater at 60f and is heated

a household hot water system heats water only as it is needed. the water enters the electric heater at 60f and is

  What is the initial pressure of the gas what is the final

1 kmol of n2 gas ideal is contained in a piston initially at 300k with a volume of 0.1 m3. the piston cylinder is well

  Compare the thermal efficiency of a two-stage gas turbine

compare the thermal efficiency of a two-stage gas turbine with regeneration reheating and intercooling to that of a

  Compute the moment of inertia of the system about an axis

small blocks each with mass m are clamped at the ends and at the center of a rod of length l and negligible mass.a

  A thermometer placed in the tank indicates the air

a 2-m3 rigid tank initially contains air at 100 kpa and 22 degrees c. the tank is connected to a supply line through a

  Show the system of equations in matrix form give a

a straight fin of uniform cross section is fabricated from a material of thermal conductivity k 5 wmk thickness w 20

  If the turbine dissipates heat to its surroundings at the

a turbine operates at steady state with steam flowing through it at a rate of 36 kgmin. the steam enters the turbine at

  If 10m3 of hydrogen at 04 mpa and room temperature is

if 10m3 of hydrogen at 0.4 mpa and room temperature is adiabatically mixed with 20m3 of nitrogen at 0.1 mpa and room

  Find the work done per pound of water during the expansion

water in a piston-cylinder initially starts at t 400of and p 200 psia. the piston is heated until it final volume is

  F 1 molemin of a mixture is 75 mol n-pentane and 25 mol

for antoine equation in the formlog10vp a- btcwith vp in mm hg and t degree c the constants for n-pentane are a6.853

  What is the maximum amount of work

No heat interactions with the environment are allowed. You do not need to describe the details of the process that produces the maximum work, but you do need to describe the final state of the blocks fully.

  The 4-mm-diameter cable bc is made of a steel with e 200

the 4-mm-diameter cable bc is made of a steel with e 200 gpa. knowing that the maximum stress in the cable must not

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd