The bar is loaded axially until it elongates 65mm and then

Assignment Help Mechanical Engineering
Reference no: EM13625409

A bar of length 2.0 m is made of a structural steel having the stress-strain diagram shown in the figure. The yield stress of the steel is 250 MPa and the slope of the initial linear part of the stress-strain curce is 200 GPa. The bar is loaded axially until it elongates 6.5mm, and then the load is removed. How does the final length of the bar compare with its original length?

Reference no: EM13625409

Questions Cloud

Liquid octane c8h18 at 25ordmc 10 atm enters a : liquid octane c8h18 at 25ordmc 1.0 atm enters a well-insulated reactor and reacts with air entering at the same
Find the work done per pound of water during the expansion : water in a piston-cylinder initially starts at t 400of and p 200 psia. the piston is heated until it final volume is
As a race car approaches a fan in the stands the fan hears : as a race car approaches a fan in the stands the fan hears the noise of the engine at 323 hz. as the race car recedes
Water exiting the condenser of a power plant at 38ordmc : water exiting the condenser of a power plant at 38ordmc enters a cooling tower with a mass flow rate of 4.5 x 107 kgh.
The bar is loaded axially until it elongates 65mm and then : a bar of length 2.0 m is made of a structural steel having the stress-strain diagram shown in the figure. the yield
A simple harmonic oscillator with frequency f 2 hz has : a simple harmonic oscillator with frequency f 2 hz has initial conditions x0 0.76m and v0 0.31 ms. calculate the
A mass on a string of unknown length oscillates as a : a mass on a string of unknown length oscillates as a pendulum with a period of 2.5 s. parts a to d are independent
A fuel pump sends gasoline from a cars fuel tank to the : a fuel pump sends gasoline from a cars fuel tank to the engine at a rate of 6.06 x 10-2 kgs. the density of the
Heights of women have a bell-shaped distribution with a : heights of women have a bell-shaped distribution with a mean of 156 cm and a standard deviation of 8cm using the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Product and engineering design review

Product and Engineering Design Review

  Combustion occurs with 20 excess air assume all fuel

a boiler is fed with a distillate fuel oil of composition c9h16o2n0.03. combustion occurs with 20 excess air. assume

  A gas in a piston-cylinder assembly undergoes two processes

a gas in a piston-cylinder assembly undergoes two processes in series. from state 1 to state 2 there is energy transfer

  The motion of a linkage in a mechanical system is examined

the motion of a linkage in a mechanical system is examined by engineers. it has been determined that the velocity of an

  Find the work and heat transfer for each process

Air in piston/cylinder at 200 kPa, 600K is expanded in a constant-pressure process to twice the initial volume (state 2). At this point, the piston is locked with a pin and heat is transferred to a final temperature of 600K. Find the work and heat..

  What is the primary growth front what is the secondary

what is the primary growth front? what is the secondary growth front? what happens when they approach each other? what

  The discharge is located 20 ft 6 m higher than the entrance

500 galmin 30 ls of 100 degree f 40 degree c water flows through 300 ft 90m of 6-inch sch 40 steel pipe. the pipe

  What is the rate at which radiation is emitted by surface

2.51 a body whose surface area is 0.5 m2 emissivity is 0.8 and temperature is 150 is placed in a large evacuated

  Calculate average velocity and mass flow rate of air

wall temperature needed for the runner to cylinder #3, such that the cylinder air inlet temperature is the same as that in cylinder #1. Runner length for cylinder #3 is 15 cm.

  Based on the above conditions determine the error when the

a pressure transducer that behaves as a second order system is used to monitor pressure fluctuations in a petrochemical

  Diameter pipe is used to maintain a constant level

Find flow rate A siphon made of a 1 in-inside-diameter pipe is used to maintain a constant level in a 20 ft-deep tank

  Compute the total equivalent resistance for the circuit for

permit a user to input a number between 1 to 10. store this value as the variable numberofresistors. this will be used

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd