The amount of mass that has escaped and c the entropy

Assignment Help Mechanical Engineering
Reference no: EM13612256

A rigid tank contains 7.5 kg of saturated water mixture at 400 kPa. A valve at the bottom of the tank is now opened and liquid is with drawn from the tank. Heat is transferred to the steam such that the pressure inside the tank remains constant. The valve is closed when no liquid is left in the tank. If it is estimated that a total of 5 kJ of heat is transferred to the tank, determine

(A) the quality of steam in the tank at the initial state?

(B) the amount of mass that has escaped, and (c) the entropy generation during this process if heat is supplied to the tank from a source at 500°C.

Reference no: EM13612256

Questions Cloud

If the power generated by the turbine is 4 mw determine the : steam expands in a turbine steadily at a rate of 25000 kgh entering at 6 mpa and 450degc and leaving at 20 kpa as a
The following information is available for flip company : the following information is available for flip company beginning inventory 600 units at 4 first purchase 900 units at
What is the calculated t value are the mean test scores of : you are conducting a study to see if students do better when they study all at once or in intervals. one group of 12
The following items were taken from the post adjusted trial : the following items were taken from the post adjusted trial balance of flip company. all balances are normal. mortgage
The amount of mass that has escaped and c the entropy : a rigid tank contains 7.5 kg of saturated water mixture at 400 kpa. a valve at the bottom of the tank is now opened and
However the current is 0540 ms and it carries the swimmer : a swimmer capable of swimming at a speed of 1.59 ms in still water i.e. the swimmer can swim with a speed of 1.59 ms
Prepare in journal form without explanations the end of : the account balances appearing on the trial balance below were taken from the general ledger of flips copy shop at
The umuc daily news reported that the color distribution : the umuc daily news reported that the color distribution for plain mampms was 40 brown 20 yellow 20 orange 10 green and
A boat is traveling upstream in the positive direction of : a boat is traveling upstream in the positive direction of thexaxis at14kmh with respect to the water of a river. the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Suppose that you have a basin of 35c warm water that you

suppose that you have a basin of 35c warm water that you use to run a heat engine that cools its substance with air at

  A specimen of aluminum having a rectangular cross section

a specimen of aluminum having a rectangular cross section 9.7 mm times 12.4 mm0.3819 in. times 0.4882 in. is pulled in

  You are working in a company that has developed a process

you are working in a company that has developed a process to produce dna vaccines from e.coli. after the fermentation

  Calculate the magnitude of the heat transfer during the

carbon monoxide an ideal gas in a piston cylinder at an initial state of 320 k 160 kpa and 0.2 m3 is compressed in an

  Determine diameter of a circular rod of ductile material

determine diameter of a circular rod of ductile material with a fatigue strength ,e=280 Mpa. Add a tensile yield strength of 350 Mpa. The member is subjected to a varying axial load from 700 kN to -300kN. Assume Kt=1.8 and factor of safety=2.

  What is the ideal mechanical advantage of the wedge

A hydraulic shear applies 2000 lb force to a wedge. It is used to shear plate steel to rough size. The shear has a 1/4 inch thick cutting blade with a 45 degree slope. What is the ideal mechanical advantage of the wedge?

  Explain the different experimentpurpose of this practical

explain the different experiment.purpose of this practical is to verify the law for parallelogram of forces law for

  A component is fully constrained with 0 dof

An engineer insists that a component is fully constrained with 0 DOF because 2 plates are bolted together with 4 screws (assuming one of the 2 plates is considered "grounded"). Is he / she correct? Explain why or why not using concepts discuss..

  What is the density of liquid al-116si alloy at the melting

what is the density of solid aluminum at the melting temperature? what is the density of liquid aluminum at the melting

  Write down the continuity equation navier-stokes equations

a wire of radius ri is coated by a process described above. it is fed to a reservoir filled with a newtonian fluid with

  What should the bungee cord''s relaxed length

As shown, a 130 lb bungee jumper wants to jump from the top of a 655 ft high bridge and be able to just touch the water below. Given that the bungee cord has a spring constant of 2.33 lb/ft, what should the bungee cord's relaxed length, l, be for ..

  Problem a tension link shown to the right is used in

problem a tension link shown to the right is used in earth-moving equipment and is subjected to cyclic stresses varying

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd