User Account

All Pages

Take the gravitational acceleration to be 981ms2 also

Assignment Help Mechanical Engineering
Reference no: EM13622982

A cylindrical tank of methanol has a mass of 40 kg and a volume of 51 L. Determine the methanol's weight, density, and specific gravity. Take the gravitational acceleration to be 9.81m/s2. Also, estimate how much force is needed to accelerate this tank linearly at 0.25 m/s2.

Reference no: EM13622982

Questions Cloud

Three blocks are attached to each other via ropes and : three blocks are attached to each other via ropes and pulleys as shown. assume the pulleys are frictionless and the
Tab inc has a 100 million face value 10 year bond issue : tab inc. has a 100 million face value 10 year bond issue selling for 95 percent of par that pays an annual coupon of
Hydrotech corp stock was 32 per share at the end of last : hydrotech corp stock was 32 per share at the end of last year. since then it paid a 1 per share dividend. the stock
One-year treasury bills currently earn 550 percent you : one-year treasury bills currently earn 5.50 percent. you expect that one year from now one-year treasury bill rates
Take the gravitational acceleration to be 981ms2 also : a cylindrical tank of methanol has a mass of 40 kg and a volume of 51 l. determine the methanols weight density and
Calculate the correlation coefficient r for the data : calculate the correlation coefficient r for the data
A 70 kg object is being pulled up a slope of 35 degrees : a 70 kg object is being pulled up a slope of 35 degrees with the horizontal so that the rope is parallel to the slope.
Suppose the us dollar and euro interest rate for the next : suppose the us dollar and euro interest rate for the next one year are 1.5 and 2 respectively. both are annually
The average life expectancy of tires produced by the : the average life expectancy of tires produced by the whitney tire company has been 40000 miles. management beliveves

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the maximum speed

A vehicle of mass 1500kg and track 1.8m has a centre of mass located centrally at 1,1m above the ground. It has to travel around a bend of 56m radius to the centre of mass.

  The pressure is constant in this process determine a mass

refrigerant 134-a is contained in a 4 ft3 tank at 160 lpfin2. at the beginning the saturated vapour occupies a volume

  Heat transfer occurs at a rate of 2 kw from the compressor

air enters a compersoor operating at steady state at 1.05 bar 300k with a volumetric flow rate of 12 m3min and exits at

  Determine the distance d between the cars

Determine the distance d between the cars at which the driver of car A must apply his brakes to just avoid colliding with carB.

  Preparing cad geometry for fea

Demonstrate suitable accuracy by using a simple hand calculation for the static analysis of the structure. Describe in detail the hand calculations performed to validate the final solution. What is the approximate error between the simplified hand..

  Drinking water at 10oc for an office complex must be pumped

drinking water at 10oc for an office complex must be pumped along a horizontal section of pvc pipe 50 m long at 2 ms.

  Find the velocity of the jet air

If the deflection of the gae fluid height, h, is 2 inches find the 1) velocity of the jet air and 2) the force exerted on the disk by the air.

  Calculate the flow velocity and the gauge pressure in such

water at a gauge pressure of 3.8 atm at street level flows into an building at a speed of 0.06 ms through a pipe of 5.0

  A particle travels along a straight line with an

a particle travels along a straight line with an acceleration of a 10-0.2s ms2 where s is measured in meters.

  Numerical method i have a numerical method project iam

i have a numerical method project iam looking for someone to do it within 24 hours with good

  Due to surface tension the pressure inside the jet will be

a 12-mm diameter jet of water discharges vertically into the atmosphere. due to surface tension the pressure inside the

  Determine the maximum axial compressive force

A short 60-mm-diameter circular bar is made of a material for which the maximum safe compressive stress is 80 MPa and the maximum safe shearing stress is 30 MPa. Determine the maximum axial compressive force that can be safely applied.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd