Steam having a specific enthalpy of 160 kjkg and pressure

Assignment Help Mechanical Engineering
Reference no: EM13626352

Steam having a specific enthalpy of 160 kJ/kg and pressure of 1 kPa enters an adiabatic pump. Upon leaving the pump, the steam is at a pressure of 1200 kPa and has a specific enthalpy of 170 kJ/kg. No kinetic or potential energy changes occur through the pump. Determine

(a) the pump work, per kilogram of steam.

(b) the average density of steam, assuming the pump is reversible in nature.

Reference no: EM13626352

Questions Cloud

Air is compressed adiabatically from 147 psia 70 to 588 : air is compressed adiabatically from 14.7 psia 70 to 58.8 psia and 76 btulbm of work is required. neglecting changes
An engineer is designing a horizontal rectangular conduit : engineering fluid mechanics 9th editionauthors crowe elger williams roberson problem 9.62 pg 313.an engineer is
Now we have to find a new material so he can spin the ball : a man tried spinning a ball round and round in the air at the end of a unknown material its a rope like structure but
A 100 ohm resistor a 12x10-6 f capacitor and a 17x10-3 h : a 10.0 ohm resistor a 12x10-6 f capacitor and a 17x10-3 h inductor are connected in series to a 155-v generator.
Steam having a specific enthalpy of 160 kjkg and pressure : steam having a specific enthalpy of 160 kjkg and pressure of 1 kpa enters an adiabatic pump. upon leaving the pump the
A contact lens is made of plastic with an index of : a contact lens is made of plastic with an index of refraction of 1.36. the lens has an outer radius of curvature of
Five kilograms of water h2o sealed in a piston-cylinder : five kilograms of water h2o sealed in a piston-cylinder device undergoes 3 quasi-equilibrium processes that complete a
Consider a wind turbine with a 90-m blade span subjected to : consider a wind turbine with a 90-m blade span subjected to 25-kmh steady winds. if the combined turbine-generator
The bullet goes completely through the target emerging at : a target in a shooting range gallery of a square wooden board of side length s 0.500 meter and mass mt 0.750 kg that

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Compute change in entropy of earth change in entropy of sun

sun a 5800 k transfers heat to earth at an average rate of 1360 w per m2 of surface area of earth. the earth has a

  An amplifier circuit has a gain of 85 db if the magnitude

an amplifier circuit has a gain of 85 db. if the magnitude of the input voltage to the amplifier is12 mv what is the

  Determine the temperature at the end of the process and the

air undergoes a polytropic expansion process in a piston-cylinder assembly from 75 psia and 300 f to 15 psia. employing

  The 05m long container shown in the figure accelerates

the 0.5m long container shown in the figure accelerates downhill so that the liquid surface is parallel to the road. a

  A turbine produces 2 mw of power while accepting steam at 3

a turbine produces 2 mw of power while accepting steam at 3 mpa and 400 c and rejecting steam at 50 kpa and 100c. find

  With manufacturing tolerance of - 10 - 40 ohms find the

the jmh company manufactures resistors with an ideal resistance value of 400 ohms. a sample of 2000 resistors were

  Determine the natural period when a 226 kg mass is attached

a 4.53 kg mass attached to the lower end of a spring whose upper end is fixed vibrates with a natural period of 0.45

  What are the percentages of the total heat absorption

What are the percentages of the total heat absorption taking place in the economizer, boiler drum and the superheater, respectively? Assume cp of air and water as 1.005 kJ/kg K and 4.2 kJ/kg K, respectively.

  A 25-hp 240-v 778-a shunt motor has an armature resstence

a 25-hp 240-v 77.8-a shunt motor has an armature resstence of 0.083 ohms and a field-circuit resistance of 125 ohms.

  Discuss at least five factors

Assume that you are one of the candidates who have impressed the recruiting team of the company. The recruiting team of XYZ Company is happy that they are willing to offer you the required job. Discuss at least five factors which you are going to con..

  Estimate the safety factor with respect to infinite fatigue

a 20 mm diameter shaft with a 6 mm diameter transverse hole is made of cold-drawn steel having ultimate strength 550

  A 02 lb block is initially moving horizontally at 5 fts

a 0.2 lb block is initially moving horizontally at 5 fts when r1 4 ft it slides around the smooth inside surface of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd