Steam enters at 300c and exits as liquid water at 90c while

Assignment Help Mechanical Engineering
Reference no: EM13612864

A stream of methanol vapor is used to chill a countercurrently flowing saturated steam in an adiabatic heat exchanger. Steam enters at 300C and exits as liquid water at 90C, while methanol enters at 5,500 STP L/min at 65C at and leaves at 260C.

(a) what is the flow rate of steam in m3/min?

(b) what is the rate of heat transfer (kW)?

Reference no: EM13612864

Questions Cloud

Air initially at a dry-bulb temperature of 45oc and : air initially at a dry-bulb temperature of 45oc and relative humidity of 10 is adiabatically humidified to 60 relative
Tsuchiya corporation manufactures a variety of productslast : tsuchiya corporation manufactures a variety of products.last year the companys variable costing net operating income
After closing the accounts on july 1 prior to liquidating : after closing the accounts on july 1 prior to liquidating the partnership the capital account balances of jessup king
Xyz companys financial statement indicates 20000 units of : xyz companys financial statement indicates 20000 units of raw material as opening stock 10000 units of raw material as
Steam enters at 300c and exits as liquid water at 90c while : a stream of methanol vapor is used to chill a countercurrently flowing saturated steam in an adiabatic heat exchanger.
Assume that you are on the board of directors of a company : assume that you are on the board of directors of a company that has decided to buy 80 percent of the outstanding stock
Consider 25 of austenite containing 065 wt c and cooled to : consider 2.5 of austenite containing 0.65 wt c and cooled to below 727 degrees c.a what is the proeutectoid phase?b how
Assuming that the visible spectrum extends from 380 to 750 : a film of oil lies on wet pavement. the refractive index of the oil exceeds that of the water. the film has the minimum
The total horizontal force exerted by the planes engine is : jus before it lifts off a 10500 kg airplane is traveling at 60 fts. the total horizontal force exerted by the planes

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Explain how can be determined the dynamic parameters

How can be determined the dynamic parameters of a second order system, wiht an Inertia (M), a dampening coeficient ( C ) and a Stiffness constant ( K).

  A 1875 inch diameter shaft machined from aisi 1018 cd

a 1.875 inch diameter shaft machined from aisi 1018 cd steel supports a bending load during operation at 1750 rpm. if

  Determine the failure envelope and the non-failure region

Determine the failure envelope and the non-failure region in the sigma_y - tau_xy plane using Tsai-Hill theory for the following cases

  Determine the amount of steam produced per hour

Determine the amount of steam produced per hour, if the total heat loss is 10% of the heat available for steam raising - What would be the new heat transfer area if the fluids were in parallel flow

  An 8-kg plunger is released from rest in the position shown

an 8-kg plunger is released from rest in the position shown and is stopped by two nested springs the constant of the

  Mainframe computing is way to manage enterprise data

Mainframe computing used to be the only way to manage enterprise data. Then personal computers changed the data management scene. How do these two computing styles differ, and how did shift to PC-based computing evolve.

  Compute the convective mass transfer coefficient when the

the sherwood number for vapor transport from the surface of a high moisture food product to the surrounding air is

  There is much consternation between your associates as to

a closed tank having a volume of 2ft3 is filled with 0.30 lb of a gas. a pressure gage attached to the tank reads 12

  Te point starts moving at t0 find the total distance

the position of a point p on a line is given by the equation x t sinpi t2. the point starts moving at t0. find the

  Calculate the force required to displace the bellow

How to calculate the force required to displace the Bellow for 10mm which is fixed in the pipe line. It is a ring type bellow and i want to find axial force.

  What is the volume occupied by the water vapor what is the

a frictionless piston-cylinder is filled with 3 liters of water at 250 kpa. initially the temperature of the water is

  Determine the initial discharge rate of water

The tank air pressure above the water level is 300kPa(absolute) while the atmospheric pressure is 100kPA. Neglecting frictional effects, determine the initial discharge rate of water from the tank.(Density of water=1000kg/m^3)

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd