User Account

All Pages

Steam enters a nozzle at 30 bars and 320c and leaves at 15

Assignment Help Mechanical Engineering
Reference no: EM13628262

Steam enters a nozzle at 30 bars and 320C and leaves at 15 bars with a velocity of 535 m/s. The mass flow rate is 8000 kg/h. Neglecting the inlet velocity and considering adiabatic flow, compute:

a) the exit enthalpy in kJ/kg

b) the exit temperature in degrees Celsius

c) the nozzle exit are in square centimeters

Reference no: EM13628262

Questions Cloud

A sample of n 25 individuals is selected from a population : a sample of n 25 individuals is selected from a population with fx 80 and a treatment is administered to the sample.
An object has a volume of 329 m3 and a mass of 3000 kg do : an object has a volume of 3.29 m3 and a mass of 3000 kg. do you expect the object to sink or float in water? if the
A rocket is launched and attains a speed of 5400 ms when : a rocket is launched and attains a speed of 5400 ms when 62000 m above the earth. if the engines shut down how much
A steel rod is 22m long amp must not stretch more then 12 : a steel rod is 2.2m long amp must not stretch more then 1.2 mm when a 8.5 kn load is applied to it.knowing that e
Steam enters a nozzle at 30 bars and 320c and leaves at 15 : steam enters a nozzle at 30 bars and 320c and leaves at 15 bars with a velocity of 535 ms. the mass flow rate is 8000
A 15 kg object floating in the water has 21 of its volume : a 15 kg object floating in the water has .21 of its volume above the surface of the water. what is the volume of the
Describe how you will design a study that will optimize : describe how you will design a study that will optimize sensitivity specificity and predictive value and minimize type
A where along the plate is t tmax b is the flow laminar or : a 10 cm2 plate has an electric heater installed that produces a constant heat flux. saturated liquid water at 10 degc
A rocket is launched and attains a spped of 7900 ms when : a rocket is launched and attains a spped of 7900 ms when 35000 m abovve the surface of the earth. if the engines then

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The general ledger of the fly-by-night fbn engineering

the general ledger of the fly-by-night fbn engineering company contained the following account balances.administrative

  The ball at is kicked such that 60 if it strikes the

the ball at is kicked such that 60 . if it strikes the ground at having coordinates 25 -25 determine the speed at

  Write a matlab code to draw a cubic bezier curve using

write a matlab code to draw a cubic bezier curve using decasteljau algorithm. the input to the program should be four

  In an experiment similar to the procedure set out for part

in an experiment similar to the procedure set out for part a of the calorimetry experiment 1.500 g of mgs was combined

  Develop a dynamic model of a trebuchet

Analysis of the motion of swing including velocity and acceleration plots of all moving parts and projectile analysis of projectile eg: flight path, horizontal distance, deceleration and launch velocity

  Knowing that it strikes the water 4 s after release

a stone is thrown vertically upward from a point on a bridge located 40 m above the water. knowing that it strikes the

  A vibrating system has a mass m 10kg suspended from a

a vibrating system has a mass m 10kg suspended from a spring of modulus k 2500nm nd damping amunts to c 45 nsm.

  Water enters a nozzle with a circular inlet are with a

water enters a nozzle with a circular inlet are with a diamter of 5 cm at a velocity of 3 ms. the outlet diameter is 2

  How do you plot an isentropic compression process on a

how do you plot an isentropic compression process on a pressure-enthalpy diagram? i know how to do it on a

  Determine the maximum contact pressure

The wheel of a crane lift is rolling on a flat rail. The radius of the wheel is 4 in, the contact length and force are 2.5 in and 1 ton respectively, and E = 30 MPa and ν = 0.3 for both parts. Determine (a) the maximum contact pressure, (b) the wi..

  Run a fmea analysis and suggest the possible solution

The plate fin heat exchanger uses gaskets to separate oil and water paths. Since this unit is used in trucks, vibration should also be considered. Run a FMEA analysis and suggest the possible solution to avoid future failure.

  100 lb of fluid food is heated by addition of 10000 btu of

100 lb of fluid food is heated by addition of 10000 btu of energy. if the food has initial temperature of 40degf and

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd