State the main reasons for the use of excitation control

Assignment Help Electrical Engineering
Reference no: EM13292843

State the main reasons for the use of excitation control usingfeedback of terminal voltage for a turbo generator supplying powerto a complex power system.

Reference no: EM13292843

Questions Cloud

At what level of pretax cost savings would be indifferent : At what level of pretax cost savings would you be indifferent between accepting the project and not accepting it?
Marketers are concerned with consumer perception : "Firms always want consumers to notice changes or modifications to their product lines." Using consumer behaviour concepts, discuss this statement. Further, discuss tactics firms may use to enhance exposure, characteristics of attention, and why mark..
Describe three methods of comparing techniques to improve : Describe three methods of comparing techniques to improve the first swing electromechanical transient behaviour of such a generator.
Consumer behaviour concepts : Suppose that your friend Kenny has created a new product: Kenny’s environmentally friendly light bulbs. Using consumer behaviour concepts, advise Kenny, in how to develop a long-term advertising strategy to advertise his new brand and range of enviro..
State the main reasons for the use of excitation control : State the main reasons for the use of excitation control using feedback of terminal voltage for a turbo generator supplying powerto a complex power system.
What would be the effect on the operating cash flow : A first analysis used straight line depreciation, but if $200,000 was recognized in year 1 as the depreciation expense, what would be the effect on the Operating Cash Flow for Year 1 if the tax rate is 40%?
Consumers are often viewed as lazy and unmotivated : Consumers are often viewed as lazy and unmotivated. Using consumer behaviour terms discussed this semester, discuss this statement. Further, explain the peripheral-route to persuasion and discuss ways marketers can influence low-effort attitudes.
Explain the energy for a mol of photons with wavelength : A certain wavelength is 1100 nm. What is the energy for a mol of photons (J/mol) with this wavelength
Define is remote line concentration economical : An analog line concentrator resides logically between the line circuits and the line side of a switching fabric. One might be placed physically at the distribution point in the loop architecture or, even at the pedestal- in which case, the line ci..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine how many bits must the adc have

An LVDT with associated signal conditioning will be used to measure work-piece motion from -20 to +20 cm. The static transfer function is 2.5 mV/mm. The output will be interfaced to a computer via an ADC.

  Frequency division multiplexing

Write a short technical report on Frequency Division Multiplexing

  Find frequency that will cause inductor to have impedance

1. Determine the capacitance for a capacitorif its impedance is 5000 ohms at 400 radians/second. 2.Calculate the frequency that will cause a100mH inductor to have an impedance of 15,708 ohms.

  Calculate the minimum number of discretely sampled data

Suppose a signal from a vibrating motor is to be sampled discretelywith a digital data acquisition system to determine the RPM of the motor. It is known that the maximum possible RPM is 1800.

  Determine how many turns does the secondary coil have

(a) If the primary coil, Nsubp has 500 turns and Vsub2=240V than, how many turns does the secondary coil have (b) If the turns ratio is 5, and Vsub2=240V, than, what is the current flowing through both coils

  Determine the value of xl in a parallel resonant circuit

how do you determine the value of Xl in a parallel resonant circuit, when all youre given is Xc, Rcoil, and the parallel resistance

  How to compare the values of h and m obtained

A "ferrite" having a relative permeability of 50 H / m, that operates with flux densities sufficiently small, may be considered a single material. If the magnetic flux density in the material is B = 0.05 T, H and M. halle How to compare the values

  Determine whether or not the system is linear

the discrete-time systems, where y[n] and x[n] are, respectively the output and the imput sequences, determine whether or not the system is (1) linear, (2) causal, (3) stable, and (4) shift-invariant: y[n] = x[n+3];

  Calculate the ampacity required in each armature conductor

A 4 pole DC generator has an armature winding containing a total of 648 conductors connected in 2 electrical parallel paths. If the flux per pole is 0.321 x 10^6 Maxwells and the speed of rotation is 1800 rpm.

  Determine the transfer of second-order highpass filter

1) Determine the transfer of second-order highpass filter with a cutoff frequency of 900 Hz and passband gain of 1 using a butterworth type. 2) Design a filter for your transfer function from question.1 using the sallen-Key topology.

  How effect do internal capacitances in the transistor model

What effect do internal capacitances in the transistor model have on practical performance of a real system? How would you use these model values to predict system performance?

  Determine the max rms voltage that can be applied

Determine the max rms voltage that can be applied to the high side of the transformer without exceeding the rated_flux_density in the core if transformer is supplied by frequency of 50 Hz.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd