User Account

All Pages

Specify a suitable temperature and wall thickness to give

Assignment Help Mechanical Engineering
Reference no: EM13627183

One design calls for a diffusion flux of 5 108 mol/m2.s, a tube radius of 0.125 m, and inside and outside pressures of 2.026 MPa (20 atm) and 0.0203 MPa (0.2 atm), respectively; the maximum allowable temperature is 450ºC. Specify a suitable temperature and wall thickness to give this diffusion flux and yet ensure that the tube walls will not experience any permanent deformation.

Reference no: EM13627183

Questions Cloud

If the particles velocity is perpendicular to the magnetic : a particle with a mass of 6.64 10-27 kg and a charge of 3.210-19 c is accelerated from rest through a potential
Assume that the inside of the tube is a force-free region : a particle of mass m is confined to a tube of length l.a use the uncertainty principle to estimate the smallest
All four sides of the plate are maintained at 20 degree c : a 50-cm by 50-cm plate of pure nickel generates 3.9 mwnr of energy uniformly within the plate. all four sides of the
A compact disc undergoes 30 revolutions as it accelerates : a compact disc undergoes 30 revolutions as it accelerates uniformly from rest to 5 revolutions per second.what is the
Specify a suitable temperature and wall thickness to give : one design calls for a diffusion flux of 5 108 molm2.s a tube radius of 0.125 m and inside and outside pressures of
A random sample of size n100 is obtained from a population : a random sample of size n100 is obtained from a population with a proportion p0.52a. what is the sampling distribution
The magnification of the final image produced by this lens : two identical diverging lenses are separated by 6.0 cm. each lens has a focal length of -12 cm. an object is placed 10
Customers come to a store as a poisson process with rate 12 : customers come to a store as a poisson process with rate 12 per hour.a compute the probability of three customers
Determine the natural frequency of this torsional system if : a pulley of moment of inertia i is fixed on a shaft of polar second moment of area j and shear modulus g. the shaft is

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Show all three states of steam on t-v diagram label states

steam enters an adiabatic turbine at 20 mpa and 600?c state 1. at an intermediate stage 20 of the inlet steam is bled

  An existing supply of 5-mm diameter music wire will be used

a helical compression spring with squared and ground ends is required to exert a maximum working force of 1000 n and a

  Determine the number of revolutions it must undergo to

a wheel has an initial clockwise angular velocity of 12 rads and a constant acceleration of 5 rads2. a determine the

  A spherical copper shell of inside radius 5cm and wall

a spherical copper shell of inside radius 5cm and wall thickness 1cm loses heat to the surrounding air which is

  What was its velocity during this time

what was its velocity during this time? (Hint: Take the origin to be the location of the radar.)

  What will be the charge on the capacitor a long time after

capacitor with capacitance 6.00 microf is connected to a resistor with r 780 o in series and an emf source of 25.0 v

  If a pound of coal produces 183 pounds of co2 during the

a hot water leak in one of the facets of your apartment can be very wasteful. a continuous leak of one quart per hour a

  Q1 15 kg of oxygen n2 and 015 kg of helium he2 are

q1. 1.5 kg of oxygen n2 and 0.15 kg of helium he2 are separated by a partition in a vessel.nbsp the nitrogen is at 5

  Explain single degree of freedom vibration problems

Single degree of freedom vibration problems with forcing functions, Need help with this Undergraduate problem where two dampers are in series.

  Pumps and heat recovery

Energy in the home, personal energy use and home energy efficiency. Efficient use of ‘waste' heat and renewable heat sources.

  Determine the pressure, temperature and enthalpy at entrance

A heat pump uses refrigerant-134a as the working fluid in an ideal vapour-compression refrigeration cycle between 0.14 and 0.8 MPa. The refrigerant leaves the compressor at a temperature of 40° C. Determine the pressure, temperature and enthalpy a..

  Determine the radius of the contact area

Assume you are given a spherical joint where the ball has a radius of 20 mm and socket has a radius of 22 mm. If the contact load is 50 N, E = 210 GPa, and ν = 0.3, determine (a) the radius of the contact area, (b) the maximum contact pressure.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd