Sketch the passage shape

Assignment Help Mechanical Engineering
Reference no: EM13217782

At a section in a passage, the pressure is 150 kPa (abs), the temperature is 10 deg C, and the speed is 120 m/s. For isentropic flow of air, determine the Mach number at the point where the pressure is 50 kPa (abs). Sketch the passage shape.

Reference no: EM13217782

Questions Cloud

How the lubricants reduce the friction : How the lubricants reduce the friction and wear characteristics of the parts in contact?
True of naturalistic studies : Which of the following is true of naturalistic studies?
Calculate the heat transfer per kilogram : Calculate the heat transfer per kilogram of air between sections (1) and (2), and the stagnation pressure at section (2).
Pursue human cloning : give three reasons someone who is against human cloning could give for scientists should not pursue human cloning
Sketch the passage shape : At a section in a passage, the pressure is 150 kPa (abs), the temperature is 10 deg C, and the speed is 120 m/s. For isentropic flow of air, determine the Mach number at the point where the pressure is 50 kPa (abs). Sketch the passage shape.
Determine the maximum torque t : a shaft is made of a steel alloy having an allowable shear stress of 12 ksi. If the diameter of the shaft is 1.5 in., determine the maximum torque T that can be transmitted. What would be the maximum torque T' if a 1 in. diameter hole is bored thr..
Create a clear angle and define your audience : submit a 2- to 3-page Profile essay written to your local community on a local person, place, or event. Your profile essay should take a specific angle that represents a significant issue, important contribution, or surprising quality of your chos..
Demographic and socioeconomic standpoint : What does the typical public school child look like from a demographic and socioeconomic standpoint?
Compares and contrasts neoclassicism-impressionism : Compares and contrasts Neoclassicism, Impressionism, and Abstract Expressionism. Use the selected artwork as your examples for each

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the force in member bc

Determine the force in member BC. After the truss is sectioned use a single equation of equilibrium for the calculation of each force. State if these member is in tension or compression. Take F1 = 2 kN , F2 = F3 = 3.8kN , F4 = 5 kN, F5 = 3 kN.

  How long is required for half the ice cube to melt

how long is required for half the ice cube to melt? State clearly all the assumptions you make in formulating your model of this problem.

  Write an appraisal of mathcad including a comparison

write an appraisal of mathcad including a comparison with mathlab. describe another feature of mathcad, giving examples of how it can be used.

  Determine the maximum allowable speed v of the crane

In an ore minig operation, a bucket full of ore is suspended from a traveling crane which moves slowly along a stationary bridge. The bucket is to swing no more than 4m horizontally when the crane is brought to a sudden stop. Determine the maximum..

  What input voltage will be computed by the adc

A successive approximation ADC has 4 bits and a reference voltage of 10 V. If the input voltage is 2.8 V, describe each step the ADC undergoes to determine the value of the 4 bits. What input voltage will be computed by the ADC?

  Calculate the lattice parameter of aluminum

Write a complete program consisting of a Main Program and Subprogram (you choose which type, but there should be only one) that fulfills the following requirements.

  Explain the maximum flow past a circular cylinder

The maximum flow past a circular cylinder is 2 X the Up stream velocity. The max velocity occurs at the center line of the top of the cylinder.

  Define steam is cooled at constant pressure until one-half

A piston-cylinder device contains 0.8kg of steam at 300 degrees C and 1 MPa. Steam is cooled at constant pressure until one-half of the mass condenses.

  Determine the maximum torque t

a shaft is made of a steel alloy having an allowable shear stress of 12 ksi. If the diameter of the shaft is 1.5 in., determine the maximum torque T that can be transmitted. What would be the maximum torque T' if a 1 in. diameter hole is bored thr..

  Determine vertical distance between two consecutive drops

Water drips at the rate of 5 drops per second from a leaking tap. Determine the vertical distance between two consecutive drops after the lower drop has attained a velocity of 3 m/s.

  Is the proposed system sound

let it cool back to the outdoor temperature, pass it through a turbine, and discharge the cold air leaving the turbine into the house. from a thermodynamic point of view, is the proposed system sound?

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd