Sketch the cycle on a t-s diagram with respect to

Assignment Help Mechanical Engineering
Reference no: EM13612444

Water is the working fluid in an ideal vapor power cycle with reheat. Superheated vapor enters the first turbine stage at 8 MPa, 500oC and expands to 2 MPa. Then, it is reheated to 500oC before entering the second turbine stage, where it expands to the condenser pressure of 7.5 kPa. The mass flow rate of steam entering the first turbine stage is 2630 kg/h. Assume a source temperature of 1500 K and a sink temperature of 300 K. Take T0 = 300 K. Sketch the cycle on a T-s diagram with respect to saturation lines and determine (a) the rate of the heat input to the working fluid, in kW, (b) the rate of the heat rejected from the working fluid, in kW, (c) the net power output, in kW, (d) the thermal efficiency of the cycle, (e) the exergy destruction associated with each of the processes, in kW, and (f) the second law efficiency.

Reference no: EM13612444

Questions Cloud

Oxygen has a molar mass of 320 the root mean square of an : oxygen has a molar mass of 32.0. the root mean square of an oxygen molecule at 294k 479 ms. what is its average
Determine a the rate of steam production b the rate of : hot exhaust gases leaving an internal combustion engine at 400oc and 150 kpa at a rate of 0.8 kgs is to be used to
Columbia enterprises is studying the replacement of some : columbia enterprises is studying the replacement of some equipment that originally cost 74000. the equipment is
An electron is released from rest at the point midway : two stationary positive point charges charge 1 of magnitude 3.50nc and charge 2 of magnitude 1.60nc are separated by a
Sketch the cycle on a t-s diagram with respect to : water is the working fluid in an ideal vapor power cycle with reheat. superheated vapor enters the first turbine stage
By using the net-present-value method determine whether stl : stl entertainment is considering the acquisition of a sight-seeing boat for summer tours along the mississippi river.
The total electric flux from a cubical box 300cm on a side : the total electric flux from a cubical box 3.00cm on a side is 1.40times103ncdot m2c. what charge is enclosed by the
The city of bedford is studying a 600-acre site on route : the city of bedford is studying a 600-acre site on route 356 for a new landfill. the startup cost has been calculated
Which of the following describes the qualitative behavior : which of the following describes the qualitative behavior of the maxwell-boltzmann distribution as temperature

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  The water level in a tank is 20 m above the ground a hose

the water level in a tank is 20 m above the ground. a hose is connected to the bottom of the tank and the nozzle at the

  Determination of the heat transfer coefficient values

this would provide you with a set of Reynolds numbers. Next, using the integral method, determine the velocity profiles within the boundary layer to be followed by determination of the heat transfer coefficient values for your selected Reynolds numbe..

  What is the cable tension

If cable spacing is 1 m into the paper, what is the cable tension.

  Calculate the reaction force in each of supports a and b

a crate containing 40 bricks each of mass 1.3kg is placed on a storage framework as shown.a calculate the reaction

  Consider a container of volume 250ml that is divided into

consider a container of volume 250ml that is divided into two compartments of equalnbspsize. in the left compartment

  Determine a the shaft torque required to prevent the

water enters vertically and steadily at a rate of 35 ls into the sprinkler shown in figure q.4. the sprinkler has

  Design a bridge

Design a bridge that will withstand 4 fully loaded semi-trailers

  Calculate the power output in kw

Air enters a turbine at 40 kN/m2, 900 C, and leaves at 10 kN/m2. The flow is reversible and adiabatic. Inlet velocity is quite low and outlet velocity is 150 m/s through a cross-sectional area of 0.20 m2. Calculate the power output in kW.

  Calculate the time for the ice to completely melt

If the chest is completely filled with ice, calculate the time for the ice to completely melt. State your assumptions. The enthalpy of fusion for water is 330 kJ/kg.

  A 120 mm diameter hole is punched in the center of the

a steel plate with dimensions shown below is subjected to 150 kn tensile force and 300 n-m bending moment. the plate is

  One pound mass of water in a piston-cylinder assembly

one pound mass of water in a piston-cylinder assembly initially a saturated liquid at 1 atm undergoes a

  Calculate the overall efficiency the heat rate mw and the

calculate the overall efficiency the heat rate mw and the total fuel rate kgs of a combined-cycle power plant 1 if no

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd