Simple inverting comparator circuit with hysteresis voltage

Assignment Help Mechanical Engineering
Reference no: EM13709629

Design a simple inverting comparator circuit with a hysteresis voltage of 120 mv and a nominal threshold of +2.5 v indicate component values.

Reference no: EM13709629

Questions Cloud

Tensile strength of the steel before and after cold-working : Using the data shown in Callister Figure 7.19, draw an approximate stress-strain curve for the 1040 steel at 0% cold work and at 30% cold work, clearly indicating the yield strength, ductility, and tensile strength of the steel before and after cold-..
Ductility compare for pure iron vs. the alloy steel : Using the data shown in Figures 6.14 (at 25oC) and 6.21, combine both curves onto one plot, being careful to correctly plot the modulus, yield strength, tensile (ultimate) strength, and ductility. Discuss how the modulus, yield strength, and ductilit..
Theoretical maximum height that a pump could pull water : Determine the theoretical maximum height that a pump could pull water up from a well (i.e. from the vacuum side of the pump). The set-up described is similar to on-farm wells. Assume that atmospheric pressure is exerted on the water at the bottom of ..
Assume compressible flow-airfoil is moving through the air : An airfoil is moving through the air at 300 mph at 15,000ft pressure altitude. The temperature recorded is 45F.(Assume Compressible Flow) At a point on the airfoil upper surface is 360 mph. What is the pressure at this point? if this be the average p..
Simple inverting comparator circuit with hysteresis voltage : Design a simple inverting comparator circuit with a hysteresis voltage of 120 mv and a nominal threshold of +2.5 v indicate component values.
Temperature distribution within chip and dielectric mount : You are a thermal design engineer and plan to design cooling solution for computer chip. As a basic design, a chip (kc = 50 W/m-K) is mounted in a dielectric substrate (ks = 5.0 W/m-K) and one surface of the system is convectively cooled, while the r..
The volumetric flow rate at the exit of the pipe : Carbon dioxide gas enters a pipe at 3 MPa and 500 K at a rate of 2 kg/s. CO2 is cooled at constant pressure as it flows in the pipe and the temperature of CO2 drops to 450 K at the exit.
Takes for the parcel to reach the speed of the belt : A parcel is lowered onto a conveyor belt that is moving at 4 m/s. If the coefficient of kinetic friction between the parcel and the belt is 0.25, calculate the time that it takes for the parcel to reach the speed of the belt.
Find the temperature and velocity of the gas : A 0.6-m diameter gas pipeline is being used for the long-distance transport of natural gas. Just past a pumping station, the gas is found to be at a temperature of 25°Cand a pressure of 3.0 MPa. The mass flow rate is 125 kg/s, and the gas flow is adi..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Design the condenser of a steam power plant that has a

design the condenser of a steam power plant that has a thermal efficiency of 40 percent and generates 10 mw of net

  Determine the entropy change of the water during process

A piston-cylinder device is insulated and contains 0.005 m3 of saturated liquid water at a constant pressure of l50 kPa. An electric resistance heater inside the cylinder is now turned on, and 1800 kJ of energy is transferred to the steam.

  Determine the temperature and phase of water

Determine the temperature and phase of water from the following information. If the phas is a vapor-liquid mixture, report the fraction of vapor and liquid.

  What is the percent span for the old and new setpoints

In order to increase production rate, a reactor setpoint was increased from 160 psig to 190 psig. The reactor pressure transmitter was recalibrated from 0- 200 psig to 0- 300 psig. What is the percent span for the old and new setpoints?

  Water is converted in a boiler from saturated liquid at 500

water is converted in a boiler from saturated liquid at 500 kpa to superheated steam at 500 kpa and 300c. find the

  Refrigerant 134a at 700 kpa and 40oc is expanded

refrigerant 134a at 700 kpa and 40oc is expanded adiabatically in a closed system to 60 kpa. determine the work

  What pressure differential in inches of hg should exist

an 8 in. id pipe is connected by means of a reducer to a 6 in. id pipe. kerosene flows through the system at 2000

  A insulated system is divided into 2 parts by a partition

an insulated system is divided into 2 parts by a partition . one part of the tank contain 2.5 kg of compressed liquid

  Find max stress sigmatheta the cylinder is hollow in the

find max stress sigmatheta. the cylinder is hollow in the center one layer of steel inside and a layer of brass

  One kilogram of water contained in a sealed piston-cylinder

one kilogram of water contained in a sealed piston-cylinder assembly initially at 160degc and 200 kpa undergoes an

  Find and list information for the polymer-shaping process

find and list information for the polymer-shaping process rotational molding. what typically is it used to make? you

  A bicyclist starts from rest after traveling along a

a bicyclist starts from rest after traveling along a straight ath a distance of 20m reaches a speed of 30kmh. find his

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd