Show states that counter will pass through with an input

Assignment Help Electrical Engineering
Reference no: EM13264715

A 3-bit binary counter counts for 0 (000) to 7 (111). The counter moves to the next state with an input of x = 0 and stays in the same state with an input of x = 1.
a. Draw the State Table and State Diagram for this 3-bit binary counter. Assume that the starting state for this counter is 0 (000).
b. Also show the states that this counter will pass through with an input of 111001 if the starting state is 0(000).

Reference no: EM13264715

Questions Cloud

Compute the average rate of formation of p2o5 : Consider the reaction: 2H3PO4=P2O5+3H20 Using the information below calculate the average rate of formation of P2O5 between 10.0 and 40.0 seconds.
Design a synchronous sequential circuit with one input line : Design a synchronous sequential circuit with one input line and one output line that recognizes the input string x = 1111. The circuit is also required to recognize overlapping sequence such that if the input string is x = 1101111111010
What is the energy range of photons : What is the energy range (in joules) of photons of wavelength 400nm to 760nm
What is the effective cost of borrowing in this case : Your firm has an average collection period of 20 days. Current practice is to factor all receivables immediately at a 1.00 percent discount.
Show states that counter will pass through with an input : A 3-bit binary counter counts for 0 (000) to 7 (111). The counter moves to the next state with an input of x = 0 and stays in the same state with an input of x = 1. a. Draw the State Table and State Diagram for this 3-bit binary counter.
How much current can be drawn at a temperature : A 1 A diode can deliver 1 A up to 75ºC with a derating factor of 8.5 mA/ ºC (this means that the current must be reduced by 8.5 mA for each degree above 75ºC). How much current can be drawn at 110 ºC
Define what is the empirical formula of a hydrocarbon : What is the empirical formula of a hydrocarbon if complete combustion or 1.900 mg of the hydrocarbon produced 6.423 mg of CO2 and 1.315 mg of H2O? Be sure to write C first in the formula.
What is the cost of preferred stick for kyle : Wilson charges a fee of 3% on the sale of preferred stock. What is the cost of preferred stick for Kyle using the investment banker?
Determine the focal length of the second lens : Object O1 is 15.0 cm to the left of a converging lens of 10.0-cm focal length. A second lens is positioned 10.0 cm to the right of the first lens, What is the focal length of the second lens

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Draw the gate-level diagram

Write the logic equation for Y in terms of A,B,C that solves this problem, and draw the gate-level diagram.

  Define the efficiency of the motor and drive system

If the efficiency of the motor and drive system is 80% and it is fed through a transistor regulator at 12V, what is the mean current through this regulator when the printer is working continuously?

  Would it be preferable to put filter before noise amplifer

A filter with a great deal of attenuation must be placed in an amplifier chain. Ignoring all considerations other than the desire to minimize noise figure, would it be preferable to put the filter before or after a low noise amplifier Why

  How to modify the circuit to eliminate the hazard

Assume that the inverters have a delay of 1 ns and the other gates have a delay of 2ns. Initially A = 0 and B = C = D = 1, and C changes to 0 at time = 2ns. Draw a timing diagram and identify the transient that occurs.

  Find how high does the listener need to mount the anntena

a high power FM station of frequency 96.9 MHz has an antenna height of 1200 feet. If the signal is to be recieved 60 miles from the station, how high does the listener need to mount their anntena in this fringe area

  Why sinusoidal wave is chosen for ac fundamentals

why sinusoidal wave is chosen for AC fundamentals rather than a simple curve such as square or triangular wave?

  Find the maximum acceleration that can be measured

An LVDT (Linear Variable Differential Transformer) is used in an accelerometer to measure seismic-mass displacement. The LVDT and signal-conditioning output is 0.31 mV/mm with a +/- 2 cm maximum core displacement.

  Calculate quasi-fermi energies relative to intrinsic energy

A piece of germanium doped with 1016 cm-3 shallow donors is illuminated with light generating 1015 cm-3 excess electrons and holes. Calculate the quasi-Fermi energies relative to the intrinsic energy and compare it to the Fermi energy in the absen..

  Calculate the energy required to change the arrival time

Calculate the energy required to change the arrival time of a near earth object of mass 10,000 MT by a distance equal to the diameter of Earth using laser ablation. Assume an ejection velocity of the material at 10,000 m/sec.

  Explain the parking lot of the spenditall megamall

The parking lot of the Spenditall Megamall has an area of 128 ac. It is partially landscaped to provide some areas of grass. Assume that an average of 63% of the water that falls on the parking lot will flow

  Calculate the end-to-end propagation time delay

A coaxial line 5.6m long has distributed parameters R=6.5ohm/m, L=3.4 uH/m, G=8.4 mS/m, and C=21.5 pF/m. If the line operates at 2MHz, calculate the characteristic impedance and the end-to-end propagation time delay.

  Find the density for germanium

Find the density for germanium (Ge) semiconductor atoms give that its lattice constant a-5.66Å (Angstrom) and atomic weight is 72.59 g/mole.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd