Sandbag is released from hot air balloon at an altitude of

Assignment Help Mechanical Engineering
Reference no: EM13624749

Sandbag is released from hot air balloon at an altitude of 1312ft. The net effect of gravity and aerodynamic friction produces an acceleration for the falling sandbag of the form a=g-cv^2, where g is the gravitational acceleration, v is the velocity and c=0.6/km. What is the velocity of the sandbag right before it hits the ground?

Reference no: EM13624749

Questions Cloud

A clinical trial tests a method designed to increase : a clinical trial tests a method designed to increase theprobability of conceiving a girl. in the study 516 babies
Two 5 cm diameter 15 cm long aluminum bars k 176 wmk with : two 5 cm diameter 15 cm long aluminum bars k 176 wmk with ground surfaces are pressed against each other with a
Four people stand at the edge must off the carousel each : a 4.2 m diameter carousel merry-go-round is freely rotating with an angular velocity of w.85 rads. its moment of
What is the range of frequencies where the power spectrum : an accelerometer was used to measure the vibrations of machinery. the sensor output was acquired during an experiment
Sandbag is released from hot air balloon at an altitude of : sandbag is released from hot air balloon at an altitude of 1312ft. the net effect of gravity and aerodynamic friction
A metal rod of length 48 cm falls toward the earth the rod : a metal rod of length 48 cm falls toward the earth. the rod is horizontal and oriented east-west. at a moment when the
Assume that you plan to use a significance level of : assume that you plan to use a significance level of alpha0.05 to test the claim that p1p2. use the given sample sizes
A series rlc circuit has a source of time-varying emf : a series rlc circuit has a source of time-varying emf providing 15 v at a frequency f0 with l 7.90 mh r 130 omega and
Telephone calls enter a switchboard at a rate of 3 calls : telephone calls enter a switchboard at a rate of 3 calls per minute. assume that any given no more than one call will

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Prove using the increse in entropy principle that the

a prove using the increse in entropy principle that the maximum thermal efficiency for any heat engine is the carnot

  Compute the convective mass transfer coefficient when the

the sherwood number for vapor transport from the surface of a high moisture food product to the surrounding air is

  A 03 kg softball has a velocity of 15 ms at an angle of

a 0.3 kg softball has a velocity of 15 ms at an angle of 35deg below the horizontal just before making contact with the

  Calculate the angular separation between the first order

Calculate the angular separation between the first order minima on either side of the central maxima when the slit has a width of 6x10-4 cm & light illuminating it has a wavelength of 6000A0?

  Determine the load on the prop

A horizontal cantilever of length L supports a load W, uniformly distributed along its length. the cantilever is proped to the level of the fixed end at a distance 3/4 L from that end. Determine the load on the prop.

  If the impact force varies with time as shown in the plot

the rubber mallet is used to drive a cylindrical plug into the wood member. if the impact force varies with time as

  Determine the velocity ratios that can be achieved

Determine the velocity ratios that can be achieved by the gear box in terms of number of teeth in the sun wheel  and determine which component (out of the sun wheel, planet carrier and annular wheel) has to be used as the input shaft to get the req..

  What would be the indicated distance

A steel tape is used to measure a distance of 20 m at a 10 0C. Assuming that the tape will measure the true distance when the temperature is 20 0C. What would be the indicated distance at 10 0C? What would be the indicated distance at 400C?

  Determine the dimensions of the lowest cost container

design an outside storage facility for methane gas ch4. 110 kg is the maximum mass of methane to be stored at this

  Calculate the outlet temperature

A compressor operating adiabatically is to compress 2.83 m^3/min of air at 29.4C and 102.7 kN/m^2 to 311.6kN/m^2. Calculate the power required if the efficiency of the compressor is 75%. Also, calculate the outlet temperature.

  At what location s will the combined moment

At what location s will the combined moment of the weights of the man and platform about point B be zero.

  Define kinetics of particles -newton''s second law

Kinetics of Particles : Newton's Second Law, Determine the maximum theoretical speed that may be achieved over a distance of 50 m by a car starting from rest

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd