Remove the top five elements from the top of the stack

Assignment Help Mechanical Engineering
Reference no: EM131336649

Assume that the top of the stack in a program is pointed to by the register SP.You are required to write program segments to perform each of the followingtasks (assume that only the following addressing modes are available:indexed, autoincrement, and autodecrement).

(a) Pop the top three elements of the stack, add them, and push the resultback onto the stack.

(b) Pop the top two elements of the stack, subtract them, and push the resultsback onto the stack.

(c) Push five elements (one at a time) onto the stack

(d) Remove the top five elements from the top of the stack.

(e) Copy the third element from the top of the stack into register R0.

Reference no: EM131336649

Questions Cloud

Equivalent annual cost calculation : (Equivalent annual cost calculation) Barry Boswell is a financial analyst for Dossman Metal Works, Inc. and he is analyzing two alternative configurations for the firm's new plasma cutter shop. Calculate each project's equivalent annual cost (EAC) gi..
Determine the annual financing cost : Determine the annual financing cost of a 6-month $20,000 discounted bank loan at a stated annual interest rate of 10 percent. Assume that no compensating balance is required.
Absolute value inequality to represent tolerance : Suppose 1.5" long bolts are made by another machine and have to be within 0.125" of 1.5". What is the absolute value inequality to represent this tolerance?
Determine wellsleys annual financing cost : The fee to the dealer for selling the issue would be $8,000. Determine Wellsley's annual financing cost of this commercial paper financing.
Remove the top five elements from the top of the stack : Pop the top three elements of the stack, add them, and push the resultback onto the stack.
Resistors and computer chips : An electronics company produces transistors, resistors and computer chips. Each transistor requires 3 units of copy, 1 of zinc and 2 units of glass. Each resistor requires 3, 2 and 1 units of the three materials and each computer chip requires 2, ..
Minimize the annual financing cost : Assuming that Brandt wishes to minimize the annual financing cost of issuing commercial paper, which dealer should it choose?
Semicontinuous and has nonempty and compact values : Let (X, d) be a metric space and F : X -> X a correspondence. If F is upper semicontinuous and has nonempty and compact values, then F has a fixed point.
Calculate the manometer reading h : Calculate the manometer reading H for a pressure of 30 psi in the air pipe. Assume an isothermal process for the air in the sealed tube.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Explain effective matching of surface roughness

Effective Matching of Surface Roughness, Concerning the effective matching of surface roughness using a lathe, I have been asked to quantify Ra = C1* s^C2 v^C3 Re^C4

  Knowing that it strikes the water 4s after release

a stone is thrown vertically upward from a point on a bridge located 40m above the water. knowing that it strikes the

  Calculate the velocity v of the collar

Calculate the velocity v of the collar as it hits the stop at B if it is elevated from rest at A by the action of the constant 40-N force in the cord. The cord is guided by the small fixed pulleys.

  How do bolt stiffness and joint stiffness affect the angle

A rubber washer has been used instead of a metal one, by mistake. How will preload be affected if the same predetermined torque and turn are used to tighten that bolt?

  A piston cylinder device contains 03kg of r134-a initially

a piston cylinder device contains 0.3kg of r134-a initially at 0 c and 400 kpa. the cylinder is then heated until the

  Setch a system of mass m which is accleerated from rest

sketch a system of mass m which is accleerated from rest to a velocity v2 raised to a height of elevation h and cooled

  What is the claimed efficiency of the engine

An inventor claims to have made an engine that operates from a plutonium energy source at 1060°R and a heat sink at 558°R. He also claims that the engine produces 4.80 hp while rejecting 16000 Btu/hr of heat.

  Cell that faces convective and radiative ht transfer

Steel-reinforced concrete pillars are used in the construction of large buildings. Structural failure can occur at high temperatures due to fire because of softening of the metal core. Consider a 200mm thick composite pillar consisting of central ste..

  A blower handles 1 kgsec of air at 20 deg c and consumes a

a blower handles 1 kgsec of air at 20 deg c and consumes a power of 15 kw. the inlet and outlet velocities of air are

  Determine the maximum allowable tensile load before

a 1 meter section of 1040 steel square tubing is loaded in tesnion. the tubing has an outer edge length of 10mm and a

  Calculate the number of vacancies per cubic meter in some

calculate the number of vacancies per cubic meter in some metal at 688degc. the energy for vacancy formation is 0.87

  Determine the number of teeth on gear 3

Two spur gears are in mesh. Driven gear 3 has a magnitude of rotational speed that is one half that of the driver gear 2. Gear two rotates at 500 rpm , has a module of 3 mm and has 48 teeth. Determine 1) The number of teeth on gear 3, 2) The magni..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd