Ratio of the heat transfer coefficient

Assignment Help Mechanical Engineering
Reference no: EM13942740

Consider laminar flow of a fluid with Pr = 4 that undergoes a combined entrance process within a con- stant surface temperature tube of length L xfd,t with a flow rate of m. An engineer suggests that the total heat transfer rate can be improved if the tube is divided into N shorter tubes, each of length LN = L/N with a flow rate of m/N.

Determine an expression for the ratio of the heat transfer coefficient averaged over the N tubes, each experiencing a combined entrance process, to the heat transfer coefficient averaged over the single tube, hD,N /hD,1.

Reference no: EM13942740

Questions Cloud

What is the level of production : What is the level of production when 10 units of labor are employed? What is the fixed cost of production when 10 units of labor are employed? What is the variable cost of production when 10 units of labor are employed
Write letter to companies you supply explaining situation : Write a letter to the companies you supply explaining the situation to them. Write a memo to your staff so they know what is happening and will be prepared to deal with any customer questions or complaints.
Can a charitable organization exempt under section : Can a charitable organization exempt under section g 501(c)(3), not a private foundation, file a group return for all of its branches if they are located in different states?
Describe the sequence of events that lead to the computation : Describe the sequence of events (loading registers from memory, saving values in memory, and so on) that lead to the computation of x + y + z. How about (2x) + y?
Ratio of the heat transfer coefficient : Determine an expression for the ratio of the heat transfer coefficient averaged over the N tubes, each experiencing a combined entrance process, to the heat transfer coefficient averaged over the single tube, hD,N /hD,1.
Knowledge of curriculum theory : What affect might the knowledge of curriculum theory have on educators and the way they manage their classrooms? (2-3 paragraphs)
Write critique on innovative product-service alter over time : Carry out a written critique of the way in which characteristics of the chosen innovative product or service has altered over time in order to suit the changing needs of the market by taking account of the following:
Important step when planning a statistical study : Determining sample-size is important step when planning a statistical study. It is also quite a difficult task since many variables must be considered.
Discuss the role of the managerial accountant in today : Discuss the role of the managerial accountant in today's business environment. How has the role changed and evolved over time?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Strain gauge is used to measure the top surface strain

A strain gauge is used to measure the top surface strain on an end loaded cantilevered beam. From the end of the beam to the location of the strain gauge is L=12.1 inches. The width of the beam is w=0.99 inches, and the the thickness of the beam is t..

  A large number of concrete slabs each 06 m in length are

a large number of concrete slabs each 0.6 m in length are lined up with a spacing of 0.1nbspmm between them. the

  The refrigerant leaves the condenser as a saturated liquid

a small vapor-compression refrigeration unit is to be built into a recreational vehicle and is designed to operate on a

  Determine the mass flow rate of combustion gases

Water enters the steam generator of the power plant shown in the figure at 7MPa, 50 degrees C, and exits at 7MPa, 600 degrees C. The steam is then fed into a well-insulated turbine, developing a power output of 31.6 MW before exiting the turbine as a..

  Tarzan king of the jungle mass 662 kg grabs a vine of

tarzan king of the jungle mass 66.2 kg grabs a vine of length 14.6 m hanging from a tree branch. the angle of the vine

  A four foot diameter reel of wire pays out 250 feet of

a four foot diameter reel of wire pays out 250 feet of conductor wire in two minutes. what is the average angular

  Air enters a compressor at 300 k and 100 kpa at a

air enters a compressor at 300 k and 100 kpa at a volumetric flow rate of 4 m3s. the air is compressed such that the

  Determine the net work output and thermal efficiency

A gas turbine power plant operates on the simple Brayton cycle between the pressure limits of 100 and 1600 kPa. The working fluid is air, which enters the compressor at 40 degrees Celsius and leaves at 650 degrees Celsius. Using constant specific hea..

  Are there alternative solutions which might also effective

how can this goal be achieved? are there alternative solutions which might also be effective?

  Your town has a proposal to install solar panels on the

your town has a proposal to install solar panels on the roof of the combined city hall - police station - fire station

  A mass of 3kg of nitrogen at 100kpa and 20oc is contained

a mass of 3kg of nitrogen at 100kpa and 20oc is contained in a piston-cylinder device. it is now expanded to a final

  Calculate limits of tolerance

Calculate limits of tolerance and allowance for a 25mm shaft and hole pair designated H8/d9

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd