User Account

All Pages

Plot the step response of the system at each value of t to

Assignment Help Mechanical Engineering
Reference no: EM13345712

Using MATLAB Simulink, set up the negative feedback system of  and find the value of the gain 
a) Plot the step response of the system at each value of t to yield over damped, under damped, critically damped and marginally stable responses
b) At the output of the negative feedback system, cascade the transfer function 

Reference no: EM13345712

Questions Cloud

Patients suffering from respiratory disorders are often : patients suffering from respiratory disorders are often treated in oxygen tents in which the atmosphere is enriched in
The concentration of a solution sodium iodide ion will be : the concentration of a solution sodium iodide ion will be determined by titrating 90 ml of it using potassium
Calculate the amount of heat required to completely sublime : calculate the amount of heat required to completely sublime 51.0 g of solid dry ice co2 at its sublimation temperature.
If coal is made up of 44 pure carbon by mass calculate the : methane can be obtained from coal using a process called the gasification of coal. the global chemical equation for the
Plot the step response of the system at each value of t to : using matlab simulink set up the negative feedback system of nbspand find the value of the gainnbspaplot the step
You are given 256 g of salicylic acid using the procedure : you are given 2.56 g of salicylic acid. using the procedure in the lab manual for the synthesis of aspirin you recover
Interpret and explain the information on the herbicide : interpret and explain the information on the herbicide label including the use of pictograms and supplemtary
An underground iron pipe in damp soil is to be protected : an underground iron pipe in damp soil is to be protected from rusting. which of the following techniques would not
A tightly sealed 50 l flask contains argon at 716 deg c and : a tightly sealed 5.0 l flask contains argon at 71.6 deg. c and 781 mm hg. the flask is heated until the pressure is

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  He uses a mercury barometer to measure the atmospheric

a mountain climber determines his altitude using atmospheric pressure and temperature measurement data. he uses a

  The coefficient of restitution is 09 between the two

the coefficient of restitution is 0.9 between the two 60-mm-diameter billiard balls a and b. ball a is moving in the

  Find the maximum permissible unbalance

A centrifugal pump, weighing 600N and operating at 1000 rpm, is mounted on six springs of stiffness 6000 N/m each. Find the maximum permissible unbalance in order to limit the steady-state deflection to 5mmm peak-to-peak.

  Determine the entropy change of the water during process

A piston-cylinder device is insulated and contains 0.005 m3 of saturated liquid water at a constant pressure of l50 kPa. An electric resistance heater inside the cylinder is now turned on, and 1800 kJ of energy is transferred to the steam.

  Specifications for steel plate to be used in the

specifications for steel plate to be used in the construction of a certain bridge call for the minimum yield to be

  Find the stagnation pressure loss

Consider a supersonic wind tunnel with test section Mach number of 2 and fixed geometry diffuser designed to operate with minimum stagnation pressure losses (smallest diffuser area).

  Find the velocity of the jet air

If the deflection of the gae fluid height, h, is 2 inches find the 1) velocity of the jet air and 2) the force exerted on the disk by the air.

  Find the shaft id needed to obtain a maximum deflection

Find the shaft ID needed to obtain a maximum deflection at the center of 3 mm if the shaft OD is 22 cm. Assume the shaft to be the same length between supports as the length of the paper roll.

  A civil engineer must design a wheelchair accessible ramp

a civil engineer must design a wheelchair accessible ramp next to a set of steps leading up to a building. the height

  Calculate the angular separation between the first order

Calculate the angular separation between the first order minima on either side of the central maxima when the slit has a width of 6x10-4 cm & light illuminating it has a wavelength of 6000A0?

  Determine the speed of collar after the applied force

the collar has a mass of 20kg and is supported on the smooth vertical rod. the attarched springsare undeformed when d=0.5m determine the speed of collar after the applied force F=100N causes it to be displaced so that d=0.3m when d=0.5m, the colla..

  Evaluate the work required and the heat transfer

Kinetic and potential energy effects can be ignored. Evaluate the work required and the heat transfer, each in kW.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd