Obtain the z transform and find the z transform

Assignment Help Electrical Engineering
Reference no: EM13686623

Problem 1: Obtain the z transform of k3

Problem 2: find the z transform of the following signals

x1(k) = Σah ,                                                                                            where a is a constant

x2(k) = K2ak

x3(k) = kAcos(Ω0k) ,                          k=0,1,2..., where Ω0 and A are constants

Problem 3: obtain the inverse z transform of X(z) = 1+ 2z +3z2 + 4z3 + 5z4 /z4

Problem 4: by using the inversion method, obtain the inverse z transform of

X1= z3+6z+1/(z -1)(z - 0.2)

X2(z) = z2 +z/(z- 0 .5)(Z2 -1A 3: +0.64)

Problem 5:

Solve the following difference equations:

y(k +2)- y(k +1)+ 0.25y(k) = u(k -2),

y(0)

=1,

y(1)

= 2

y(k +2)- y(k +1) + 0.25y(k) = u(k +2),

y(0)

=1,

y(1)

= 2

Solve this problem for y(k), k=3,1,2... both analytically and numerically using MATLAB.

For the numerical solution, solve the problem for the first 30 samples. Plot both analytical and the numerical results in the same figure.

Reference no: EM13686623

Questions Cloud

Global economy and what it means to technology management : The Global Economy and What it Means to Technology Management - Make sure you have a wrap-up paragraph to tie everything together.
Differentiate between qualitative and quantitative research : Determine what questions the authors are trying to answer by doing this research and differentiate between qualitative and quantitative research methods and terminology. Specify which approach is used in the study.
Calculate ultimate bearing capacity of the raft foundation : Meyerhof method to calculate the ultimate bearing capacity - Use the Meyerhof method to calculate the ultimate bearing capacity of the raft foundation and the allowable bearing capacity
Explain how data is collected online : Explain how data is collected online then create a brief ethical argument for or against social media data collection methods and How can new technologies help those with disabilities? Please provide two examples.
Obtain the z transform and find the z transform : Obtain the z transform and find the z transform - solve the problem for the first 30 samples. Plot both analytical and the numerical results in the same figure.
What conditions are likely to make it possible for sand : What conditions are likely to make it possible for sand and gravel from the Sault Ste. Marie region to be sold routinely in the Southern Ontario market?
Emerging performance management topics : Create a post that presents your view of one or two key emerging performance management topics in current academic or professional debates. Provide references. Present the topics discussed in the articles and explain their importance to the field ..
Find the cumulative distribution function : Determine the probability that a patient will make it through 600 days without a recurrence and sketch the Cauchy probability density function. sod show that that f(z) is symmetric about x 0.
What steps might be taken to increase the recovery of solid : Question- After recrystallization a student obtained a very low percent recovery of a solid. Describe a probable cause of this problem and explain what steps might be taken to increase the recovery. Provide complete description

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Describe any compromises or inefficiencies the introduces

Describe how you would use the voltage follower so the output load voltage (as measured with a scope probe) agrees with the value shown on the function generator front panel independent of load impedance. Describe any compromises or inefficiencies..

  Find voltage v1 for which the diode just starts to conduct

Given the following circuit, in which R1 = 200 (Ohm), R2 = 100(Ohm), V1 = 6 V, and V2 = 3 V. Assume the diode turn-on voltage is 0.7 V. Find the current through the circuit. Find the voltage V1 for which the diode just starts to conduct.

  Write down the generic form of the convolution integral

For x(t) --> Linear System --> y(t), x(t) = u(t)-u(t-1) and h(t) = 2e^-t*u(t)  Sketch x(t) and h(t) Write down the generic form of the convolution integral Calculate y(t) for t 1, using the convolution integral method.

  What is the minimum output voltage of the ratio detector

What is the minimum output voltage of the Ratio detector. When the maximum discriminator output voltage is fed into an audio amplifier, the amplifier drives 100 Watts into an 8 ohm load. What is the dB gain of the audio amplifier.

  Calculate the expected voltage and current

Calculate the expected voltage and current in the branches of sample electric circuits and estimate the error propagation using resistor nominal values and associated tolerances.

  Describe the rise time-the overshoot and the settling time

Discuss the sequence of actions that occur in the operation of the control system for a traffic light that includes sensors in the roadbed. Indicate which actions are time-driven and which actions are event-driven.

  How can be use a nand gate to make a not gate

Interface TTL logic to 120 VAC lamp. In this part of the lab, you will interface lowpower solid state electronics to the "outside world" by switching the 120 VAC lamp on and off using the AND gate from the previous experiment.

  Determine the equivalent capacitence of the combination

a network has a 5-muF capacitence in series with the parallel combination of a 12 mu-F capacitence and an 8mu-F capacitence. Sketch the circuit diagram and determine the equivalent capacitence of the combination.

  What are the gains outside the dead band

Consider this follower to be driven by the output of a differential amplifier of gain 100 whose positive-input terminal is connected to the input signal source vs and whose negative-input terminal is connected to the emitters of the follower.

  Determine the number of binary digits required to encode

A compact disc (CD) records audio signals digitally by usingPCM. Assume that the audio signal bandwidth equals15kHz. a) If theNyquist samples are uniformly quantized into L = 65536 levels andthen binary-coded

  A micrometer caliper is used to measure the diameter of a

a micrometer caliper is used to measure the diameter of a bolt and a reading of 0.768 inches is obtained. based on

  Determine the output voltage for op-amp comparator circuit

Determine the output voltage for an op-amp comparator circuit with a non-inverting input reference voltage of + 2 VDC and an inverting input signal of - 1 VDC. The op amp reaches output saturation voltages of + or -13 V at the limits.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd