User Account

All Pages

Obtain the output response signal assuming a first order

Assignment Help Mechanical Engineering
Reference no: EM13610169

A temperature measurement device with a time constant of 0.15 seconds outputs a voltage that is linearly proportional to temperature. The device is used to measure an input signal of the form T(t)= 115+ 12sin 2t degrees C a.) Obtain the output response signal assuming a first order instrument and a static sensitivity of 5 mV/ degrees C. b.) Determine the dynamic error and time lag in the steady response. T(0) = 115 degrees C.

Reference no: EM13610169

Questions Cloud

Abis corporation uses the weighted-average method in its : abis corporation uses the weighted-average method in its process-costing system. this month the beginning inventory in
Castlevania company lost most of its inventory in a fire in : castlevania company lost most of its inventory in a fire in december just before the year-end physical inventory was
Find the electric field magnitude and direction a at the : four protons are placed at the corners of a square of side length a 1.0 angstrom. the square is in the x y quadrant of
Barrow manufacturing produces made-to-order backyard pools : barrow manufacturing produces made-to-order backyard pools. during the year barrow accepted a customer order that
Obtain the output response signal assuming a first order : a temperature measurement device with a time constant of 0.15 seconds outputs a voltage that is linearly proportional
Sanker inc has provided the following data for the month of : sanker inc. has provided the following data for the month of august. there were no beginning inventories consequently
A testing bureau reports that the mean for the population : a testing bureau reports that the mean for the population of graduate record exam scores is 500 with a standard
The august 31 balance shown on the bank statement is 9810 : the august 31 balance shown on the bank statement is 9810. there is a deposit in transit of 1260 at august 31.
Unit 6 gaap application-conceptual framework of accounting : unit 6 gaap application-conceptual framework of accounting the conceptual framework allows for the systematic

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Detemine the normal and shearing stresses

Knowing that the pipe has inner and outer dimensions equal to 35 and 42 mm, respectively, detemine the normal and shearing stresses at point a and point b.

  Describe the differences among the three plc types

Describe the differences among the three PLC types : rack/slot address based, tag based, and soft PLCDescribe the differences among the three PLC types : rack/slot address based, tag based, and soft PLC.

  Water flows through a pipe at an average temperature of

water flows through a pipe at an average temperature of t70degc. the inner and outer radii of the pipenbspare r16cm and

  Diameter pipe is used to maintain a constant level

Find flow rate A siphon made of a 1 in-inside-diameter pipe is used to maintain a constant level in a 20 ft-deep tank

  A metal is being cast into a cylinder

A metal is being cast into a cylinder which is 10 cm in diameter and 20 cm tall. The mold is bottom-gated (see class notes for geometry)

  It is pressurised internally until the outer layer surface

a thick cylinder has an inside diameter of 60 mm and an outside diameter of 100 mm. it is pressurised internally until

  Determine the work done by a 1-lb fluid system as it

determine the work done by a 1-lb fluid system as it expands slowly within a piston-cylinder arrangement from an

  Heat transfer occurs until the volume on the inside of the

a piston-cylinder device contains 1 kg of h2o. the water is at 800oc and a pressure of 20 mpa. heat transfer occurs

  Does this engine satisfy the increase of entropy principle

a heat engine whose thermal efficiency is 40 percent uses a hot reservoir at 700 k and a cold reservoir at 280 k. a

  The motor is 15 in long and 10 in in diameter the a area is

a 1.5 hp motor is operarating in a room with air t of 20 c. the motor has an efficency of 78. the motor gives off heat

  Develop an equation for the volume of the oil as a function

you are working as a summer intern at a company and a fellow intern obviously an u of a engineering student accidently

  Positive displacement and dynamic air compressors

With reference to basic constructional features, contrast the methods of compression employed by positive displacement and dynamic air compressors.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd