Living plant leaf is an open system that exchanges energy

Assignment Help Mechanical Engineering
Reference no: EM13710307

A living plant leaf is an open system that exchanges energy (sunlight and thermal flows) + matter (O2, CO2, water vapor, etc.) with the surroundings (the exterior). Even with irreversible processes (energy dissipation) we find that the net entropy change for the system + surroundings can decrease; i.e. dS < 0. Using equations presented in lecture and your own critical thinking: a) explain how this is possible in terms of deS and diS. b) Explain how the Second Law remains valid for this case.

Reference no: EM13710307

Questions Cloud

Separation of variables method to the schrodinger equation : Apply the separation of variables method to the Schrodinger equation for the hydrogen atom in spherical coordinates. The solutions for the three ordinary differential equations obtained in step 1 should be found in a Math textbook. Please make sure t..
What is the value of maximum stress and nominal stress : A circular rod with a diameter of 32.4mm has a groove cut to a diameter of 27mm. A full radius of 2.97mm is produced at the bottom of the groove. Compute the maximum stress in the rod when an axial tensile force of 42kN is applied.
What are the temperature and pressure at the nozzle exit : Room temperature atmospheric air is accelerated by a nozzle steadily from a low velocity to a velocity of 220 m/s. If the nozzle diameter decreases by a factor of 2:
Pressure difference between the inlet and the test section : A water filled manometer is attached to the inlet and the test section of a low speed wind tunnel which has the contraction ratio of 3. what would be the pressure difference between the inlet and the test section in terms of inches of water in order ..
Living plant leaf is an open system that exchanges energy : A living plant leaf is an open system that exchanges energy (sunlight and thermal flows) + matter (O2, CO2, water vapor, etc.) with the surroundings (the exterior). Even with irreversible processes (energy dissipation) we find that the net entropy ch..
Refrigerant is saturated at the inlet to the compressor : A vapor compression refrigeration cycle using R-134a as the working fluid has an evaporator temperature of -20°F, and a condenser pressure of 140 psia. The refrigerant is saturated at the inlet to the compressor and at the exit of the condenser. The..
Steam turbine operating at steady state produces : A steam turbine operating at steady state produces 6,000 hp with a heat transfer to the surroundings at a rate of 360,000 Btu/hr. Steam enters at 600 F, at 200 psi and exits as a saturated vapor at 8 psi. Neglecting the KE and PE determine the volume..
What is the heat transfer associated : Air in a piston-cylinder device is compressed from an initial state (temperature = 80 °C, pressure = 100 kPa, volume = 0.3 m3) to a final state (temperature = 250 °C, pressure = 600 kPa), during a polytropic process (n = 1.28094065700868). What is th..
Determine the temperature of the air at the exit : Air enters a pipe at 25 Celsius, 100 kPa at a flow rate of 36 m3/hr. A heater on the outside of the pipe draws 8 amps at a voltage of 120 V. All the heat from the heater is transferred to the air (well insulated and wall t is small).

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the change in the internal energy and enthalpy of

the state liquid water is changed from 50 pisa and 50 f to 200 pisa and 100 f. determine the change in the internal

  You are designing a remote-area power supply based on a

you are designing a remote-area power supply based on a miniature wind turbine that is 20 efficient. meteorological

  Determine the velocity v of each sphere as the rods pass

the two 1.5-kg spheres are released from rest and gently nudged outward from the position theta0 and then rotate in a

  Helium gas is contained in a rigid vessel

Helium gas is contained in a rigid vessel of 0.5 m3 at 500 kPa. The gas is agitated violently by a stirrer that transfers 250 kJ of work to the gas. Assuming that the system undergoes an adiabatic process, determine the final pressure of the gas. Ass..

  A piston has an area of 500 mm2 what mass must the piston

a piston has an area of 500 mm2. what mass must the piston has if it exerts a pressure of 50 kpa above atmospheric

  The differential gage attached to the pitot static tube

carbon tetrachloride s.g. 1.60 flows through a 3-in radius pipe. the differential gage attached to the pitot static

  What is the rate of flow of cooling water through the

consider an ideal steam cycle that combines the reheat cycle and the generative cycle. the net power output of the

  A 60 g bullet moving with a speed of 500 ms strikes a 5 kg

a 60 g bullet moving with a speed of 500 ms strikes a 5 kg block moving in the same direction with a speed of 30 ms. if

  By how much will the bullets miss the target

a hunter aims directly at a target 140 meter away. if the bullet leaves the gun ay a speed of 280 m/s, by how much will the bullets miss the target?

  Find the minimum required diameter of the bolt to the

a structural support is installed within a space craft. the support is made of 7075-t6 aluminum plut t-ult 250 mpa and

  However test conditions limit the available power to 400 kw

axial flow coolant pump for one lop pressurized nuclear reactor has 75 m head 6m3s flow rate 1440rpm 800 mm diameter

  Question 1approximate the torque and power necessary to

question 1approximate the torque and power necessary to rotate the inner 20 cm diameter cylinder shown in figure 1. sae

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd