Knowing the coefficient of kinetic friction between b and c

Assignment Help Mechanical Engineering
Reference no: EM13611418

A 30 g bullet is fired with a horizontal velocity of 450 m/s through 3-kg block B and becomes embedded in carrier C which has a mass of 30 kg. After the impact, block B slides 0.3m on C before coming to rest relative to the carrier. Knowing the coefficient of kinetic friction between B and C is 0.2, determine (a) the velocity of the bullet immediately after passing through B, (b) the final velocity of the carrier.

Reference no: EM13611418

Questions Cloud

On jan 2008 xyz collections alarge manufacturing and : on jan 2008 xyz collections alarge manufacturing and retailer of high-end womans apparelposted lackluster sales for the
Determine the initial acceleration of the boat if it is : the 200-kg boat is powered by the fan which develops a slipstream having a diameter of 0.75 m. if the fan ejects air
Harris fabrics computes its predetermined overhead rate : harris fabrics computes its predetermined overhead rate annually onthe basis of direct labor hours. at the beginning of
What voltage will your voltmeter read across the second : suppose after charging a 4 microf capacitor to 9 v you connect it to the second uncharged capacitor of 11 microf. what
Knowing the coefficient of kinetic friction between b and c : a 30 g bullet is fired with a horizontal velocity of 450 ms through 3-kg block b and becomes embedded in carrier c
Suppose you were given the task of estimating the : suppose you were given the task of estimating the proportion of drivers in troy al who text while they drive. discuss
A 20 nc point charge is placed on the x axis at x 20 m and : a 20 nc point charge is placed on the x axis at x 2.0 m and a -25 nc point charge is placed on the y axis at y - 3.0
Timmy tee the new administrator for the surgical clinic was : timmy tee the new administrator for the surgical clinic was trying to figure out how to allocate his indirect expenses.
Esther is a physician with her own practice she has : esther is a physician with her own practice. she has developed contracts with several large employers to perform

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Evaluate the maximum bending moment

Draw the shear force diagram for the beam and determine the position and magnitude of the maximum bending moment.

  Determine the minimum force p required to initiate motion

a force p acts on a block having a mass of m with the block resting on a rough incline. the coecients of static and

  The collector transfers heat by natural convection to the

a flat plate solar collector 6 ft by 12 ft is mounted on the roof of a house. the outer surface of the collector is at

  Determine the distance between a and b after 3 minutes

two ships a amp b are moving at constant velocities. at t0 the position of ship a is 2.41 miles east and 3.14 miles

  Determine the internal normal force

Determine the internal normal force, shear force, and moment at point C in the simply supported beam. Point C is located just to the right of the 1500 couple moment.

  Determine the following 1 the compressor work kjkg 2 the

an ideal cold air-standard brayton cycle engine operates with air entering the compressor at 27 c. the pressure ratio

  This means that the crystal structure of a cu-ni alloy

cu and ni form a substitutional solid solution. this means that the crystal structure of a cu-ni alloy consists of ni

  Determine how high the water solution will rise in a tree

nutrients dissolved in water are carried to upper parts of plants by tiny tubes partly because of the capillary

  A steel ring of mean diameter 250 mm has a square section

a steel ring of mean diameter 250 mm has a square section 2.5 mm by 2.5 mm. it is split by a narrow radial saw cut. the

  Steam enters a diffuser at 20 psia and 240of with a

steam enters a diffuser at 20 psia and 240of with a velocity of 900 fts and exits as saturatednbspvapor at 240of and

  Determine the moment about c of that force

A wooden board AB, which is used as a temporary prop to support a small roof, exerts at point A of the roof a 57-lb force directed along BA. Determine the moment about C of that force.

  Compute the concentration of li that is required

Aluminum-lithium alloys have been developed by the aircraft industry to reduce the weight and improve the performance of its aircraft. A commercial aircraft skin material having a density of 2.47 g/cm3 is desired. Compute the concentration of Li (..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd