Its about how to measure an increase in wind velocity

Assignment Help Mechanical Engineering
Reference no: EM13626558

It's about how to measure an increase in wind velocity through a restriction.It starts with an area that is 17' wide by 14' high by 20' deep and it's a right triangle with a 16 degree slope. I need to know the increase in wind velocity that would occur if there were a 25mph wind and a 35 mph wind going through this right triangle from the base and through a 10'' opening in the top, that's 10'' by 17' So it starts at 17' by 14' and ends up 10'' by 17',what is wind speed at the opening?

Reference no: EM13626558

Questions Cloud

A lead bullet with a mass of 002 kg traveling at 198 ms : a lead bullet with a mass of 0.02 kg traveling at 198 ms strikes an armor plate and comes to a stop. if all the energy
A disk has a radius of 2 cm and weighs 12 kg what is the : a a disk has a radius of 2 cm and weighs 12 kg. what is the required constant moment to rotate the disk from rest to a
Natural gas with a lower heating value lhv of 45000 kjkg is : natural gas with a lower heating value lhv of 45000 kjkg is burned on a gas stove with a combustion efficiency of 94.7
After the car has stopped what is the change in temperature : a 881 kg car is going 26 ms and the driver has to slam on his brakes to prevent an accident. assume that a total of
Its about how to measure an increase in wind velocity : its about how to measure an increase in wind velocity through a restriction.it starts with an area that is 17 wide by
Water vapor at 30 mpa and 300c state 1 is cooled to : water vapor at 3.0 mpa and 300c state 1 is cooled to 200cstate 2 then is isothermically compressed to 2.5mpa state 31.
Sap from a maple tree contains 5 sugar and 95 wateer on a : sap from a maple tree contains 5 sugar and 95 wateer on a dry basis. your evaporator will boil away 1.25 kg of water
The following is a set of data from a sample of n 11 items : the following is a set of data from a sample of n 11 items x 7 5 8 3 6 10 12 4 9 15 18 y 21 15 24 9 18 30 36 12 27 45
A bottle containing 66 kg mass of water at a temperature of : a bottle containing 6.6 kg mass of water at a temperature of 28.2 oc is placed in a refrigerator where the temperature

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the smallest horizontal force required to pull

determine the smallest horizontal force required to pull out wedge a. the crate has a weight of 200 and the coefficient

  Calculate the heat emitted to the environment btusec the

a 600 mw coal-fired power plant has an overall thermal efficiency of 38. it is burning coal that has a heating value of

  How far has the mass moved when its velocity is 243 ms

a hollow cylinder is made by welding two thin disks on either side of a thin ring. it is mounted on a axel and a 2 kg

  Use work and energy to determine the center of mass

bar ab of mass m and mass moment of inertia i 112ml2 is constrained to move within the channel as shown. the bar is

  Calculate the pressure of methane gas

Calculate the pressure of 15.0g of methane gas in a 1.50L vessel at 45.0 degrees C using (a) the Ideal Gas Law and (b) the van der Walls equation using the following information about the constants, a and b: a = 2.253 and b = 0.04278.

  Find the moment of the 12-n force about the origin the

find the moment of the 12-n force about the origin. the force is parallel to the x-axis and 5cm in the y-direction and

  Steam enters a steady flow turbine at 30mpa 1000degc with a

steam enters a steady flow turbine at 30mpa 1000degc with a flow rate of 10kgs. thirty percent of the inlet mass of

  Determine the reactions at o and the cable tensions

the light right-angle boom which supports the 400-kg cylinder is supported by three cables and a ball-and-socket joint O attached to the vertical x-y surface. Determine the reactions at O and the cable tensions.

  What is the ideal mechanical advantage of the wedge

A hydraulic shear applies 2000 lb force to a wedge. It is used to shear plate steel to rough size. The shear has a 1/4 inch thick cutting blade with a 45 degree slope. What is the ideal mechanical advantage of the wedge?

  During a constant-pressure process it is found that the

during a constant-pressure process it is found that the change in entropy is equal to 0.25cp. if the cp is constant and

  Calculate the height h to which the ball rises

A ball is thrown vertically up with a velocity of 91 ft/sec at the edge of a 190-ft cliff. Calculate (a) the height h to which the ball rises and (b) the total time t after release for the ball to reach the bottom of the cliff.

  Find the elasticity modulus 02 offset yield strength

an aluminum alloy specimen brought to tensile test had frac12 inch2 cross sectional area. it was tested to fracture and

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd