It is desired to redue this by a factor of 100 while

Assignment Help Mechanical Engineering
Reference no: EM13642801

The heat input to a cold box is to be reduced by adding extruded polystyrene sheets ( p=55kg m^-3 , k=0.027W m^-1 K^-1 , Cp=1.21kJ kg^-1 K^-1) to all sides. The box is 3 feet on a side and all sides are in contact with air. when the box is placed in a constant-temperature room which is maintained at 70 degrees F, the heat loss is 40,000 Btu h^-1. It is desired to redue this by a factor of 100 while maintaining the inside temperature at -30 degrees F. find the appropriate insulation thickness in inches.

Reference no: EM13642801

Questions Cloud

A 117 kg piece of metal at 949 c is placed in 481 g of : a 11.7 kg piece of metal at 94.9 c is placed in 481 g of water at 26.1 c in an insulated container. the metal and water
Displacement 1 is in the yz plane 580deg from the positive : displacement 1 is in the yz plane 58.0deg from the positive direction of the y axis has a positive z component and has
If the power output is 5 mw determine a the mass flow rate : steam enters an adiabatic turbine at pressure 6 mpa temperature 600oc and velocity 80 ms and leaves at pressure 50
Two of the capacitors are in parallel and this parallel : you have three 3.0 uf micro farads capacitors. two of the capacitors are in parallel and this parallel combination is
It is desired to redue this by a factor of 100 while : the heat input to a cold box is to be reduced by adding extruded polystyrene sheets p55kg m-3 k0.027w m-1 k-1
A positive point charge q 37times10-5 c is fixed at the : a positive point charge q 3.7times10-5 c is fixed at the origin of coordinates and a negative charge q -4.1times10-6
Condenser pressure is 01 bar assuming that the isentropic : a steam power plant utilizes the rankine cycle. steam enters the turbine at 50 bar and 500oc respectively. condenser
A sample of lead has a mass of 4000 kg and a density of : a sample of lead has a mass of 40.00 kg and a density of 1.130 x104 kgm3 at 0degc. assume the average linear expansion
If 500 j of work are required to carry a charged particle : if 500 j of work are required to carry a charged particle between two points with a potential difference of 20 v the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The drag characteristics of an airplane are to be

the drag characteristics of an airplane are to be determined by model tests in a wind tunnel operated at an absolute

  A cube of aluminum 10 cm on each side is initially at a

a cube of aluminum 10 cm on each side is initially at a temperature of 300degc and is immersed in a fluid at 100degc.

  Steam flows steadily through an adiabatic turbinethe inlet

steam flows steadily through an adiabatic turbine.the inlet conditions of the steam are 6 mpa400 degree celcius and 80

  Estimate a the percentage chain in toque accompanying a 20

an axial turbine of high hub-tip ratio runs with zero degree reaction and peak efficiency at design flow and speed. the

  A room 3 by 3 by 3 m has one side wall maintained at 260 c

a room 3 by 3 by 3 m has one side wall maintained at 260 c. the floor is maintained at 90 c. the other four surfaces

  Determine heat transfer required in the reheat unit kjkg if

consider a gas turbine with turbine staging and reheating. it operates under the following conditions.inlet air at 285

  Determine the resulting stress equations

Determine the resulting stress equations for σx, σy and τxy given the Airy's stress function ? = a1x^4 + a2(x^3)y + a3(x^2)(y^2) + a4x(y^3) + a5(y^4), where ai are constants. Also determine, if any, the restrictions between constants.

  The duration of the impact is 0001 s and the watch bounces

a fragile object dropped onto a hard surface breaks because it is subjected to a large impulsive force. if u drop a

  A household refrigerator that has a power input of 450 w

a household refrigerator that has a power input of 450 w and a cop of 2.5 is to cool five large watermelons 10 kg each

  Find densities, enthalpies and efficiency for gas

find densities, enthalpies and efficiency for gas turbine power cycle with the following conditions.

  The tank is allowed to exchange heat with the surroundings

a tank of compressed air is at 40 degrees c and 10 atm. 1 third of the gas is removed for inflating a car tire. the

  Exiting stream 3 is at 079 mpa and is know to contain a

high pressure steam steam 1 at a rate of 1000kgh initially at 3.5 mpa and 350 c is expanded in a turbine to obtain

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd