Is claim justified if a 90-percent confidence level is use

Assignment Help Electrical Engineering
Reference no: EM13269844

The resistance of coil manufactured by a certain company is claimed to have a mean value of resistance of 100 ohms. A sample size of 50 coils is taken and it is found that the sample mean is 115 ohms and the sample standard deviation is 10 ohms. a) Is the claim justified if a 95% confidence level is used? b) Is the claim justified if a 90% confidence level is used?

Reference no: EM13269844

Questions Cloud

Relevant customer strategy for research and development : According to the authors, what common interest do enterprises and customers now share in the context of privacy? Which is the most relevant customer strategy for research & development? All of the following are points to consider in creating a privac..
Continuously compounded lump sum investment : Investment A is a 13 year annuity that features end of month $1500 payments and has an interest rate of 7.5% compounded monthly. INvestment B is a 7 percent continuously compounded lump sum investment also good for 13 years. how much money wo..
Assume that passwords are limited to use of the 95 printable : Assume that passwords are limited to the use of the 95 printable ASCII characters and that all passwords are 10 characters in length. Assume a password cracker with an encryption rate of 6 million encryptions per second.
Explain how initial conditions are to be handled : Design a device that creates a voltage that is a damped oscillation with a frequency of 5 radians per second and a time constant of 3 seconds. In particular, explain how initial conditions are to be handled.
Is claim justified if a 90-percent confidence level is use : The resistance of coil manufactured by a certain company is claimed to have a mean value of resistance of 100 ohms. A sample size of 50 coils is taken and it is found that the sample mean is 115 ohms and the sample standard deviation is 10 ohms.
What are the impacts of the immigration on british society : What are the impacts of the immigration on British society - Please take some examples from the texts below and use your own knowledge for doing this essay.
Command line interface : The use of a CLI (command line interface) provides flexibility and power for the user who knows how to use the CLI effectively. But, effective usage of a CLI requires learning and deeper understanding of the system than that possessed by the typic..
How much mass should be attached to the spring : spring stretches by 0.0186 m when a 3.24-kg object is suspended from its end. How much mass should be attached to this spring so that its frequency of vibration is f = 5.53 Hz
Why is public support for the police important : Why is public support for the police important? How have the various model nations attempted to create or maintain public support of their police forces? Are there elements of policing in the model countries that likely hinder levels of public suppor..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the mid point of the voltage divider

An n-channel JFET needs a NEGATIVE voltage applied to its GATE, relative to its SOURCE. If you have a single POSITIVE supply applied to the MASTER loop of a JFET, the mid point of the voltage divider will also be a positive voltage

  Estimate the flux of carbon atoms into the steel

Steel surfaces can be hardened by carburization. During one such treatment at 1000°C, there is a drop in carbon concentration from 5 to 4 at% carbon between 1 and 2 mm from the surface of the steel. Estimate the flux of carbon atoms into the steel

  Compute the normalized pole frequency and sketch a pole-zero

Design a second-order band-pass filter for a system with sampling frequency of 18 kHz that is tuned for f=5kHZ The filter should not have any sample delay (the numerator and denominator orders are equal)

  Give the numerical value of the poles and zeros

a) Express the s-domain impedance of this series combination as a rational function, b) Give the numerical value of the poles and zeros of the impedance and verify your calculation by matlab.

  How to obtain resistances for an electronic circuit design

Suppose your circuit laboratory has the following standard commercially available resistors in large quantities: Using series and parallel combinations and a minimum number of available resistors, how would you obtain resistances for an electronic..

  Find the snr at the output and noise figure

an amplifier with a 1 MHz bandwidth and a 20 mV input signal. The input noise = 1 mV, output signal = 6.0 mV, and output noise = 1 mV. Find: (a) SNR at the input (b) SNR at the output (c) Noise figure

  Find the simplest expression for the outputs using k-maps

design a combinational circuit that, when given a 3-bit binary number as an input, will produce a binary number equal to the square of the input number as an output. Find the simplest expression for the outputs using K-maps.

  Find input current and power factor at maximum torque

A 500 hp, three-phase, 2200 V, 60 HZ, 12-pole, Y-connected, wound-rotor induction motor has the following parameters: R1 = .225 ohm : R'2= .235 ohm Xeq = 1.43 ohm and Xm = 31.8 ohm and Rm = 780 ohm

  Calculate the average voltage across the load

A single-phase, half-wave SCR circuit is used to control the power consumption of an inductive load. The resistive component of the load is 5 Ohm. The source voltage is 120 V (rms). When the triggering angle is adjusted to 60 degrees

  Design two sections with an order of 2

determine the transfer function of a 4th order lowpass butterworth filter with a 3-dB cutoff frequency of 3.4 kHz and passband gain=1. Design the circuit using MFB topology. Design two sections with an order of 2.

  Find the magnitude of electric field at all points in space

Find the magnitude of the electric field at all points in space both inside and outside the slab, in terms of x, the distance measured from the central plane of the slab. What is the field for x = 1.00 cm What is the field for x = 8.00 cm

  What was the bullets speed with frictionless block

A 1.12 kg block is attached to a horizontal spring with spring constant 3500 N/m. The block is at rest on a frictionless surface. A 10 g bullet is fired into the block, in the face opposite the spring, and sticks.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd