Investigate the sensitivity of the peak-to-rms value

Assignment Help Electrical Engineering
Reference no: EM131384367

The Newman phase selection criterion7 relies on selecting the phase of the kth tone of a multitoned signal according the quadratic expression given by

1228_65889582-72b5-4593-85e2-8454b9f8c913.png Using this equation, determine the phases of the 50-tone multitone signal of Problem 8.23 and compare its peak-to-RMS value to the ideal value of 3.35. Investigate the sensitivity of the peak-to-RMS value by changing the phase of each tone by 1% and computing the change in the peak-to-RMS value.

Reference no: EM131384367

Questions Cloud

Plot a multitone signal consisting of three unity amplitude : Using MATLAB or an equivalent software program, plot a multitone signal consisting of three unity amplitude sine waves with frequencies of 1, 5, and 11 kHz over a UTP of 1 ms. Assume that the phase shifts are all zero.
Did big business violate marias rights in terminating her : Maria worked for Big Business, Inc. and qualified for FMLA leave. Her husband, George, suffered from serious medical conditions, and Maria looked after him, transporting him to medical appointments, cooking for him, giving him his medications, hel..
Construct a scatterplot : An insurance company is interested in determining whether life insurance coverage is influenced linearly by disposable income. A randomly chosen sample of size 20 produced the data shown in given Table. Construct a scatterplot.
Computing the change in the peak-to-rms value : Provide a plot to illustrate your result. Investigate the sensitivity of the peak-to-RMS value by changing the phase of each tone by 1% and computing the change in the peak-to-RMS value.
Investigate the sensitivity of the peak-to-rms value : Investigate the sensitivity of the peak-to-RMS value by changing the phase of each tone by 1% and computing the change in the peak-to-RMS value.
How do those laws define discrimination based on sexual : How do those laws define discrimination based on sexual orientation? What remedy do those laws provide when there has been discrimination based on sexual orientation? Are those laws successfully addressing discrimination based on sexual orientation..
Determine the phases of each tone : Determine the phases of each tone such that the peak-to-RMS value approaches the ideal value of 3.35.
Describe the source of your information : Health care reform begins with the Affordable Care Act, and it flows down in many ways to state policy making. Note one such flow-down and describe the source of your information.
How many cycles are completed in one utp : What is the nearest coherent frequency to 20 kHz when 512 samples are collected at a rate of 44 kHz? How many cycles are completed in one UTP?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Explain which is controlled by a fast 8-4 otp-rom chip

In addition, you have a 32-Kbyte Flash chip, a 16-Kbyte SRAM chip, and a 16 KByte DPRAM chip. You want to locate the FLASH chip right in the beginning of the address space, the SRAM chip just after it, and the DPRAM at the end of the address space..

  Determine the address accessed by each of the instructions

Assuming DS = 1200H, BX = 0100H, and SI = 0250H, determine the address accessed by each of the following instructions. Assume real mode operation.  (a) MOV [100H], DL (b) MOV [SI+100H], EAX

  What is the clearance requirement for three-wire service

What is the clearance requirement for a 120/240 V, single-phase, three-wire service at the point of attachment to the building Over the driveway Over the main roadway

  Line voltage of a delta-connected generator

Calculate the frequency and line voltage of a delta-connected generator with the following characteristics:

  What is the electric field at z=3m in v/m

What is the potential with respect to infinity at a distance Z above the center of this disk?

  What precaution should be taken to prevent latch-up

What will cause latch-up in a CMOS IC. What might happen in this condition. What precaution should be taken to prevent latch-up.

  Find out the voltage that must be applied to high voltages

Find out the voltage that must be applied to the high voltage winding in order to provide rated voltage at the load under full-load conditions at 0.80 lagging power factor.

  How to combine several resistors to get the desired value

Design a load resistor (resistance rating and power rating) network to have the transformer operate at full load. Design a second network for half load. You may need to combine several resistors to get the desired value.

  Could it be dangerous to touch the exposed end of the wire

Sitting in front of you is a box; you cannot see iside the box. The box has a power cord that is plugged into a working wall socket. There is a wire coming out of the box; the end of the wire outside the box is exposed (not insulated) and is not c..

  Develop a functional design for a system that measures speed

Develop a functional design for a system that measures and displays the speed of a bicycle. Be sure to clearly identify the design levels, function requirements, and theory of operation for each level.

  Calculate the angle with respect to b at equilibrium

A circular coil of 200 turns of radius a=60mm, total resistance R=2 ohm, and no self inductance is rotated about a vertical diameter with uniform angular velocity =200 rad/s in a horizontal magnetic flux B of 0.25 Tesla.

  Calculate the amplitude and frequency of the transducer

Explain why an orifice plate meter is suitable for this application.- Estimate the required orifice plate hole diameter if the transmitter has an input range of 0 to 1.25 x 104 Pa.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd