User Account

All Pages

Interesting heat-transfer project-numerical analysis

Assignment Help Mechanical Engineering
Reference no: EM13718994

Propose an interesting Heat-Transfer project that includes a numerical analysis to determine temperatures and heat rate or heat flux. Include the following:

i. Object, device or system description and sketch.

ii. What is known and unknown, and why is it important to find unknowns?

iii. How you would analyze it analytically

iv. How you would analyze it numerically

v. Other factors related to such a project.

Reference no: EM13718994

Questions Cloud

What is the claimed efficiency of the engine : An inventor claims to have made an engine that operates from a plutonium energy source at 1060°R and a heat sink at 558°R. He also claims that the engine produces 4.80 hp while rejecting 16000 Btu/hr of heat.
Determine the change in the specific entropy of air : Air is expanded from 315 psia and 650 F to 96 psia and 40 F. Assuming constant specific heats at room temp, determine the change in the specific entropy of air.
Determine final equilibrium temperature and total entropy : A 15.9-kg aluminium block initially at 197 C is brought into contact with a 17-kg block of iron at 92 C in an insulated enclosure. Determine the final equilibrium temperature and the total entropy change for this process.
What is the fathers role in decision : What is the fathers role in decision, considering the historical and contextual role of fathers in making decisions regarding pregnancy?
Interesting heat-transfer project-numerical analysis : Propose an interesting Heat-Transfer project that includes a numerical analysis to determine temperatures and heat rate or heat flux. Object, device or system description and sketch.
Determine the voltage gain and calculate the current : Determine the voltage gain and calculate the current - Is the circuit capacitive or inductive and explain.
Energy transfer by heat into the system : A system consisting of 2 kg of water initially at 160 C, 10 bar undergoes an internally reversible, isothermal expansion during which there is an energy transfer by heat into the system of 2700 KJ. Determine the final pressure (in bar) and work (in K..
Inlet-outlet air temperature of centrifugal flow compressor : The inlet and outlet air temperature of a centrifugal flow compressor are 70oF and 120oF respectively (See Figure 1). The air flow steadily at a mass flow rate of 24 lbm/min. If the compressor is adiabatic, determine the rate of work at which the air..
Turbine operated in two stages in series using steam : A steady-state, well insulated turbine operated in two stages in series using steam . The first stage has an efficiency of 85% and the second stage 90%. Steam enters the first stage at 400 C degree and 4 MPa and exits at 1.5 MPa.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Stray heat transfer from the heat exchanger may be

consider an air-water heat exchanger. air flowing steadily at the rate of 0.5 kgs enters the heat exchanger at 100 kpa

  Steam leaves the turbine and the steam mass flow rate

A simple ideal rankine cycle has pressure limits of 3 MPa to 15 MPa, the quality of the steam leaves the turbine cannot be less than 0.95, the net output work rate generated by the cycle must be grater than 7.5 MW, try to determine the temperature of..

  Air at -55 f 4 psia and m25 enters a constant area

air at -55 f 4 psia and m2.5 enters a constant area isentropic process and leaves the isentropic process at m0.2

  A power plant operates a regenerative rankine cycle

A power plant operates a regenerative Rankine cycle with a reheat, one closed and one open feedwater heater and has a net power output of 1.2 x 109 Btu/hr. When the steam exits the boiler it's temperature is 1000°F and its pressure is 1400psi...

  What should be the testing speed for the model in the wind

a one sixth scale model of an automaobile is to be tested in a wind tunnel at a speed corresponding to the prototype

  What is the value of heat transfer coefficient at this

the temperature profile at a location in water flowing over a flat surface is -800y experimentally measure to be tdegc

  A particle at rest is located at point 325 with units of

a particle at rest is located at point 325 with units of ft. it is subjected to an acceleration in units of fts2 of a

  The rods are connected with gears having radii of 120 and

the rods ab and cd each have a 30-mm diameter and are 1m long. the modulus of the rods is 28 gpa. the rods are

  Develop an algebraic expression in the form of an integral

a cross section of a rotating bearing is shown. the spherical member rotates with angular speed omega a small distance

  Find the force required for the direct extrusion of

find the force required for the direct extrusion of commercially pure aluminum 1100-o billet 8 in in diameter into a

  Determine number of atoms contained within each of plane

Assuming that within metal crystals, the atoms can be considered as hard spheres in contact, sketch arrangement of atoms in a (100) plane, a (110) plane and a (111) plane of face-centered cubic structure. Determine the number of atoms contained wi..

  Diffusive jumps will be made from the body center atom

structure of body- centered cubic bcc crystal.a. the body-center atom in a conventional bcc unit cell has

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd