Initially the air in this tank is at 20 psia and 70 degrees

Assignment Help Mechanical Engineering
Reference no: EM13607782

A scuba divers 2 cubic foot air tank is to be filled with air from a compressed air line at 120 psia and 100 degrees F. Initially the air in this tank is at 20 psia and 70 degrees F. Presuming that the ank is well insulated determine the temperature and mass in the tank when it is filled to 120 psia.

Reference no: EM13607782

Previous Q& A

  A two-stage missile is fired vertically from rest with

a two-stage missile is fired vertically from rest with acceleration as shown in the graph. in 15 sec the first stage a

  1 a box contains 5 green 6 red 2 yellow and 8 blue marbles

1. a box contains 5 green 6 red 2 yellow and 8 blue marbles. four marbles are drawn from the box at the same time.a

  Given the following prepare the entries that both the

given the following prepare the entries that both the purchaser and seller should record for these transactions. assume

  Its specific heat ratio is 14 and gas constant is 0287

an open brayton cycle engine operates with a compressor-pressure ratio of 6 an inlet temperature of 20 c and inlet

  Toms wife dina owns a printing business in town tom works

toms wife dina owns a printing business in town. tom works in the accounts payable department of jiffy lube company.

  A charge of 18 nc is uniformly distributed along a straight

a charge of 18 nc is uniformly distributed along a straight rod of length 3.0 m that is bent into a circular arc with a

  What is the speed of the ball bearing right after it loses

a spring with a spring constant of 230.6 nm is compressed by 0.251 m. then a steel ball bearing of mass 0.0441 kg is

  Determine the efficiency and the horsepower output if the

a four-stroke-cycle engine operates on the air-standard diesel cycle. the engine has six cylinders with a 0.105 m bore

  For the current pay period the computer prog worked 60

consultant 2310 per week overtime-not applicable 3 withholding allow.comp. prog. 34 per hour 1.5 times hourly rate for

  If the friction mep is 122 bar in both cases determine the

a certain generating power plant requires 1 mw output. two types of diesel- engine installations are available. one

Reviews

Write a Review

 

Similar Q& A

  A house has a composite wall of plaster board lp 10mm k072

a house has a composite wall of plaster board lp 10mm k0.72 wm.k fibre glass insulation lb100mm k1.4 wm.k and plywood

  Assume the water is at constant density as it flows

liquid water enters a manifold series of pipes at 1080 psi and 125 degf with a mass flow rate of 3.5 x 10 6 lb hr and

  Draw in third angle projection

Draw in Third Angle Projection. the following orthogonal views - a Sectional Side View from 8 on a vertical cutting plane through the centre line of the bearing journals

  Construct a 90 two-sided confidence interval on mean life

the service life of a battery used in a cardiac pacemaker is assumed to be normally distributed. a random sample of 10

  Use potential flow theory to determine the lift coefficient

use potential flow theory to determine the lift coefficient of a spinning baseball in terms of the forward velocity v

  The rope holding the load is cut a how will the load move

a baloon rises with a constant velocity.a load is tied by a rope to the basket. when the baloon is at altitude h0 the

  Determine the minimum thickness of fibreglas insulation

Determine the minimum thickness of fibreglas insulation that needs to be used in the wall in order to avoid condensation on the outer surfaces.

  Compute the number of kilograms of hydrogen that pass per

compute the number of kilograms of hydrogen that pass per hour through a 5-mm thick sheet of palladium having an area

  How much toque docs the motor need to supply in n-m in

a rigid well insulated container contains 10 kg of water. a motor connected to a paddle wheel is used to stir the water

  The temperature of the inner surface of this pipe is 50 c

hot water flows through a pvc k.092 wmk pipe whose inner diameter is 2 cm and outer is 2.5 cm. the temperature of the

  At t 0 a force of the form f bt2e-lambdat is applied in

a particle of mass m is at rest at the origin of a coordinate system.nbsp at t 0 a force of the form f bt2e-lambdat

  Calculate the longitudinal engineering strain

A paper clip is made of wire 0.7 mm in diameter. If the original material from which the wire is made is a rod 25 mm in diameter, calculate the longitudinal engineering strain and true strain that the wire has undergone during processing.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd