In which direction should go to reach the treasure

Assignment Help Electrical Engineering
Reference no: EM13250544

The treasure map in the figure gives the following directions to the buried treasure: "Start at the old oak tree, walk due north for 530 paces, then due east for 130 paces. Dig." But when you arrive, you find an angry dragon just north of the tree. To avoid the dragon, you set off along the yellow brick road at an angle 60? east of north. After walking 400 paces you see an opening through the woods.

1) Which direction should you go to reach the treasure?

2) How far should you go to reach the treasure?

Reference no: EM13250544

Questions Cloud

Determine the final speed of each disk : Two shuffleboard disks of equal mass, one orange and the other yellow, are involved in an elastic, glancing collision. Determine the final speed of each disk
Evaluate the standard enthalpy change : Calculate the standard enthalpy change, the standard entropy change, and the standard free energy change for the reaction: N2 (g) + 3 F2 (g) ? 2 NF3 (g) How will the sign of ?G change as the temperature increases
Explain the implications of the work ethic sheehy describes : Explain the implications of the work ethic Sheehy describes for the future of American business.
How many turns are in the coil : a circular wire coil with resistance 1.4 and an area 5.0x10^-3m^2 lies perpendicular to a magnetic field that's increasing at 2.0T/s, how many turns are in the coil?
In which direction should go to reach the treasure : The treasure map in the figure gives the following directions to the buried treasure: "Start at the old oak tree, walk due north for 530 paces, then due east for 130 paces. Dig." But when you arrive, you find an angry dragon just north of the tree..
Explain what is the best oxidizing agent : What is the best oxidizing agent of these four? Could provide an explanation
Find the speed of the clay immediately before impact : A 10.0-g wad of sticky clay is hurled horizontally at a 110-g wooden block initially at rest on a horizontal surface. what was the speed of the clay immediately before impact
Find work does the racquet do on the ball : A tennis player receives a shot with the ball (0.060 0 kg) traveling horizontally at 52.5 m/s and returns the shot with the ball traveling horizontally at 38.5 m/s in the opposite direction
Prepare a scope statement for a coffee shop : Prepare a scope statement for a coffee shop. Remember to be tangible, measurable, and specific. The components: Project Objective, Deliverables, Milestones, Technical Requirements, Limits and Exclusions.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What are some of the benefits of smart grid

Would you be willing to have a Smart Meter connected to your house and collecting your electric usage information and sharing it with your local utility company?

  Explain what is the name of the standard unit cell

A 3-D cubic unit cell contains four atoms whose centers are positional halfway up along each of the vertical cell edges and one atom each centered in the middle of the top and bottom faces. Make a sketch of the unit cell.

  What was the bullets speed with frictionless block

A 1.12 kg block is attached to a horizontal spring with spring constant 3500 N/m. The block is at rest on a frictionless surface. A 10 g bullet is fired into the block, in the face opposite the spring, and sticks.

  Find the series element for circuit has lagging power factor

find the series element or elements that must be in the enclosed container to satisfy the following conditions. a. average power to circuit = 300W b. circuit has a lagging power factor

  Write a program to genrate a square wave

assuming XTAL=11.0592 MHz,write a program to genrate a square wave of 20 Hz frequency on pin2.3?

  Calculate lost torque-opper loss and efficiency

A 100V dc series motor has an armature resistance of 0.2 ohm and field resistance of 0.25 ohm. The motor runs at a speed of 600 rev/min when the shaft torque is 27.14 Nm. Friction and windage losses at this speed are 300W.

  Locate and specify an appropriate sensor

Locate and specify an appropriate sensor if it is to operate at 120 vac as an input to a PLC. Create the ladder diagram program to accomplish the specified control.

  How many turns are required for a circular loop

How many turns are required for a circular loop of 100-mm radius to develop a peak emf of 10mV if the loop rotates 30r/s in the earth's magnetic field Take B = 60E-6T.

  What transmitter powers are needed at each transmitters

Assuming a 24 dB link margin is needed to account for fading and loss due to heavy rainfall on the longest link, while 12 dB link margin is sufficient for the shorter link, what transmitter powers are needed at each of the four transmitters

  Draw the logic diagram for the four-bit circuit

Draw the logic diagram for the 4-bit circuit, using full adders and multiplexers. Determine the arithmetic operation performed for each of the four combinations of S and Cin: 00, 01, 10, and 11.

  Express the boolean function in sum of products

1. Express the Boolean function f(X,Y,Z) = XY  + X(Y + Z) in sum of products form showing the sum all nonzero minterms. 2. Express the Boolean function f(A,B,C,D) = A(B + BC) + ACD in sum of products form showing the sum all nonzero minterms.

  Sketch the system block diagram

Select an appropriate QAM signal constellation, carrier frequency, and the roll-off factor of a pulse with a raised cosine spectrum that utilizes the entire frequency band. Sketch the system block diagram and the spectrum of the transmitted signal..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd