Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1) AC and DC:
a) If have a DC circuit must use current limiting resistors on all loads that are dc so will not blow the dc parts up.
b) If an AC circuit you do not need to worry about current limiting resistors cause motors and coils, and transformers that use AC only consume what current they need when run and do not blow up unless there is a short then the current goes straight to ground and fries the motor or coil.
c) In DC and AC circuits use P=IV to make sure have enough power to support all loads. So why in part (a) and (b) for DC need to worry about current limiting resistors and for AC do not? Ohms law is ohms law. I see DC is a flat line and AC is a ripple,close to a line like 3 phase, but still ripple.
Treat the planet's atmosphere like a parallel plate capacitor. Use the parallel-plate capacitor equations.
A TTl gate with VIH (min) = 2.25 V and VIL (max) = 0.65 V is being driven by a gate with NOH (min) = 2.4 V and VOL (max) = 0.4 V. What is the maximum amplitude of noise spikes that can be tolerated on the inputs in both the HIGH and LOW states
Explain why the ionic contribution to the dielectric constant vanishes at frequencies greater than about 1GHz. 2. What is the relative permeability of a magnetic core material if the magnetizing field, H, saturates the core material?
When a 0.900kg mass oscillates on an ideal spring, the frequency is 1.49Hz . A)What will the frequency be if 0.300kg are added to the original mass. Try to solve this problem without finding the force constant of the spring.
Consider two continuous signals f(x, y) and g(x, y) that are separable, show that their convolution is also separable. Show that the 2-D Fourier transform of the rect function is the sinc function.
the conditional jumps can be predicted with 60 accuracy and the loop jumps can be predicted with 90 accuracy. the
The current in the bias resistors should be no more than 10 percent of the drain current- Determine VGS, ID, and VDs. Sketch the load line and plot the Q- point.
a DC shunt machine ( 24kW, 240V, 1000 RPM) has Ra= .12 ohms, Nf= 600 turns/pol. The machine is operated as a seperately excited dc generator and is driven at 1000 RPM. When If = 1.8 amps the no load terminal voltage is 240V.
The spring of the pressure gauge shown in the figure below has a force constant of 1385 N/m, and the piston has a radius of 1.00 cm. As the gauge is lowered into water, what change in depth causes the piston to move in by 0.750 cm
Consider and electron in a cubical crystal of a conducting material. Such an electron is free to move throughout the volume ofthe crystal, but can't escape to the outside.It is trapped in athree dimensional infinite well.
Due to increased electricity demand in the factory it is proposed to make a connection to the grid through two 2 MVA transformers in parallel each with a reactance of 0.1 pu. The fault level at the grid connection point is 1000 MVA. What will now ..
An electrical device is designed to draw 4.0 amps. A 0.5 mm diameter copper wire is used to connect the device to a power source. What is the maximum allowable length of wire (in m), if the voltage across the wire is not supposed to drop by more t..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd