User Account

All Pages

Ignoring the heat transfer changes in potential energy and

Assignment Help Mechanical Engineering
Reference no: EM13629271

Hot air steadily enters a gas turbine at 5 bar, 900 K and exits at 1 bar, 600 K and a velocity of 100 m/s. The mass flow rate of air is 10 kg/s. Ignoring the heat transfer, changes in potential energy, and the kinetic energy in inlet, calculate (a) The power output from this turbine, in kW. (b) The cross-section area of the exit, in m2.

Reference no: EM13629271

Questions Cloud

These capacitors are then disconnected from their batteries : a 2.70of capacitor is charged to 500v and a 3.70opf capacitor is charged to 530v .part a these capacitors are then
A piston-cylinder device initially contains 007 m3 of : a piston-cylinder device initially contains 0.07 m3 of nitrogen gas at 130 kpa and 120 oc. the nitrogen is now expanded
In a premlinary test of the microsort method of gender : in a premlinary test of the microsort method of gender selection 14 couples were treated and 1.3 of them had baby
A 30-kg aluminum block initially at 140 c is brought into : a 30-kg aluminum block initially at 140 c is brought into contact with a 40-kg block of iron at 60 c in an insulated
Ignoring the heat transfer changes in potential energy and : hot air steadily enters a gas turbine at 5 bar 900 k and exits at 1 bar 600 k and a velocity of 100 ms. the mass flow
Estimate the critical value of t for a 99 confidence : estimate the critical value of t for a 99 confidence interval with degrees of freedom df equal to
Consider the isothermal expansion of 450 mol of an ideal : consider the isothermal expansion of 4.50 mol of an ideal gas at 450 k from an initial pressure of 12.0 bar to a final
The journal of american medical association reported on an : the journal of american medical association reported on an experiment intended to see if the drug prozac could be used
In each case locate the state on sketches of the t-v and : in each case locate the state on sketches of the t-v and p-v diagrams.a four kg of water at 100c fill a closed

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Drmine a the temperature of the air at the compressor

the turbocharger of an internal combustion engine consists of a turbine and a compressor. hot exhaust gases flow

  Explain longitudinal versus transverse vibrations in a bar

Longitudinal versus Transverse Vibrations in a bar, A 48 inch long by 2 inch diameter round steel rod (E=30e6 psi, density=0.28 lb/in3) is fixed at one end and free at the other. If the rod is struck transversely so that there is both a longitudin..

  Compressed liquid water at 42 c and 8 mpa steadily flows

compressed liquid water at 42 c and 8 mpa steadily flows into a boiler and exits as a saturated vapor at 8 mpa. the

  Determine the new perigee and apogee altitudes of the

a satellite is in a circular orbit 250 mi above the surface of the earth. determine the new perigee and apogee

  Knowing that p 75 n and q125 n determine graphically the

tow forces p and q are applied as shown at a point a of a hook support. knowing that p 75 n and q125 n determine

  Determine the air outlet temperature

(a) Find the rate of heat transfer (kW) to the water. (b) Draw a schematic of the system. (c) Determine the air outlet temperature (°C)

  1 kg of air is allowed to expand reversibly in a cylinder

1 kg of air is allowed to expand reversibly in a cylinder behind a piston in such a way that the temperature remains

  How many kilograms each of pearlite and the proeutectoid

How many kilograms each of pearlite and the proeutectoid phase form? Schematically sketch and label the resulting microstructure.

  A car is moving with a constant speed of 40 kmh along a

a car is moving with a constant speed of 40 kmh along a straight road which heads towards a large vertical wall and

  The system is then heated while the pressure is held

consider a piston-cylinder system containing 0.1 kg of water. initially the volume of the system is 0.0125m3 while the

  Kic for the aluminum alloy used in making a structure is

kic for the aluminum alloy used in making a structure is 45mpam0.5. if the structure contains a crack 2.5mm long what

  Show the cycle on a t-s diagram with respect to the

consider a 210mw steam power plant that operates on a simple rankine cycle. steam enters the turbine at 10mpa and 500oc

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd