Ignoring the heat transfer changes in potential energy and

Assignment Help Mechanical Engineering
Reference no: EM13629198

Hot air steadily enters a gas turbine at 5 bar, 900 K and exits at 1 bar, 600 K and a velocity of 100 m/s. The mass flow rate of air is 10 kg/s. Ignoring the heat transfer, changes in potential energy, and the kinetic energy in inlet, calculate (a) The power output from this turbine, in kW. (b) The cross-section area of the exit, in m2.

Reference no: EM13629198

Questions Cloud

A missile with a conical nose cone with a semivertex angle : a missile with a conical nose cone with a semivertex angle of 16 deg is flying through sea level air at a speed of 817
A two-phase liquid-vapor mixture of h2o has a temperature : a two-phase liquid-vapor mixture of h2o has a temperature of 300oc and occupies a volume of 0.05 m3. the masses of
The compressor turbine of a simple gas turbine each have : the compressor turbine of a simple gas turbine each have isentopic efficiencies of 90. the compressor pressure ratio is
If the friction force on the side walls can be neglected : we have a laminar fully developed channel flow of water with density 1000 kgm3 and kinematic viscosity 1.3x10-6 m2s.
Ignoring the heat transfer changes in potential energy and : hot air steadily enters a gas turbine at 5 bar 900 k and exits at 1 bar 600 k and a velocity of 100 ms. the mass flow
Five kilograms of water initially a saturated vapor at 100 : five kilograms of water initially a saturated vapor at 100 kpa is cooled to saturated liquid while the pressure is
A fluid viscosity10-2 nsm2 density 800 kgm3 flows with a : a fluid viscosity10-2 nsm2 density 800 kgm3 flows with a mean velocity of 4 cms in a 10 cm smooth pipe.a. what is the
Assume that womens heights are normally distrubted with a : assume that womens heights are normally distrubted with a mean 62.4 inches and a sd given by 2.6 inch.a. if a woman is
A section of a roller-coaster is a horizontal cylindrical : a section of a roller-coaster is a horizontal cylindrical helix. the velocity of the cars as they pass point a is 15

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Estimate the extent of reaction monomer conversion

nylon 12 is produced by step growth polymerization.a estimate the extent of reaction monomer conversion necessary to

  One leg of the manometer is open to the atmosphere p101325

a tank contains a gas at an absolute pressure of 104.0 kpa. the pressure in the tank is measured using a mercury p13.59

  The minimum and maximum temperatures in the engine are 290

the compressor and turbine of a simple gas turbine engine each have isentropic efficiencies of 95. the compressor

  Providing domestic hot water to a household typically

providing domestic hot water to a household typically requires 107 kj of energy per year. a typical electric water

  Determine a the inital acceleration of the projectile b the

a projectile enters a resisting medium at x0 with an initial velocity of vo900fts and travels 4 inches before coming to

  It is pressurised internally until the outer layer surface

a thick cylinder has an inside diameter of 60 mm and an outside diameter of 100 mm. it is pressurised internally until

  Determine the temperatures of surface 1 through 4 of the

determine the temperatures of surface 1 through 4 of the furnace cavity of example 13.3 if the entire furnace

  A boiler receives a constant flow of 5000 kgh liquid water

a boiler receives a constant flow of 5000 kgh liquid water at 50 bar and 20 degrees c and it heats the flow such that

  Assuming that r-134a is an ideal gas what would the

assuming that r-134a is an ideal gas what would the specific volume of r-134a at 40 deg c and 0.06 mpaabsolute? how

  Part-1suppose that a simple pendulum is attached to our

part-1suppose that a simple pendulum is attached to our spring-damper-mass system. a simple schematic of the model is

  The amount of energy transfer to the gas by work is 45 btu

carbon dioxide co gas initially at t1 530 r p1 15 lbfin2 and v1 1 ft3 is compressed in a piston-cylinder assembly.

  If the allowable shear stress in the bolt is 13000 psi what

a horizontal beam ab with cross-sectional dimensions b 0.75 in x h 8.0 in. is supported by an inclined strut cd and

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd